Rikon Power Tools 34-260 Скачать руководство пользователя

Страница: 10 / 20

ASSEMBLY

FIG. 7

FIG. 6

FIG. 5

Install the Stop Rods.

Two stop rods and adjustable stop collars are

supplied for installation on the left and right of the

machine base. They can be set to restrict the left

or right movement of the lower sliding table, so

boring of long mortise holes will be accurate and

consistent if multiple work pieces are drilled.

1. Slide an adjustable Stop Collar Assembly

(#74, 75) onto each of the Stop Rods (#76), and

lightly tighten them in place so that they do not

move. FIG. 5.

2. Loosen the two Set Screws (#56) that are

located on the machine base’s dovetail way, just

above the holes bored to take the stop rods.

FIG. 6.

3. Insert the stop rods into the base holes and

secure them in place by tightening the set screws

that were loosened in step 2. FIG. 6.

NOTE:

The stop collars can moved along the

stop rods and also rotated so that the adjustable

locking Handles (#74) do not interfere with the

sliding table.

Install the Tool Holder

(#16) onto the upper left

side of the column using two hex Screws with

Washers (#18). FIG. 7.

Installing the Mortising Chisel and Drill Bit

The 34-260 Mortiser uses 1”, 3/4” or 5/8”

diameter shank chisels with a 3” cutting depth.

1. Open the chuck access Cover (#14)(A) and

loosen the side bushing set Screw (#86)(B).

FIG. 8.

2. The Mortiser’s head comes bored with a

1” diameter hole for chisels with 1” shanks.

For other diameter chisels shanks, the use of

the 3/4” or 5/8” bushing is required. Install the

Insta

ll the bushing (FIG. 8, C), if n

eeded, and

slightly tighten the bushing set screw to keep the

bushing in place.

FIG. 8

Continued on page 11

SET

SCREW

FOR

STOP ROD

Содержание 34-260





















Результаты поиска

Содержание 34-260

Отзывы:

Похожие инструкции для 34-260

Бренды по названию

Популярные бренды

Rikon Power Tools 34-260, Руководство оператора

Результаты поиска

Содержание 34-260

Отзывы:

Похожие инструкции для 34-260

Бренды по названию

Популярные бренды