background image

22

9. MODES

Note

When operating correctly, the stove may not be overheated. However 

Improper operation can shorten the life expectancy of electrical components 

(blowers, motors and electrical control) and is not allowed!

Pellet operation manual/automatic/comfort

MANUAL MODE

The pellet burner start and stop (ON / OFF button) and set the desired heat 

output (PLUS / MINUS button) can be done on the touch screen directly at the 

HOME main menu.

AUTOMATIC MODE

The exchange between standby and hibernation (ON / OFF button) and set the 

desired heat output (PLUS / MINUS button) can be done on the touch screen 

directly at the HOME main menu.

In AUTO mode, the heating times can be activated and the heating times can 

be programmed.

The pellet burner start is in standby mode (ON) within the heating times (or 

always at deactivated heating times).

The pellet burner stop is outside the heating times.

In the hibernation (OFF) no pellet burner start is possible, the system is turned 

off.

COMFORT MODE

The exchange between standby and hibernation (ON / OFF button) and set the 

desired room temperature (PLUS / MINUS button) can be done on the touch 

screen directly at the HOME main menu.

In the COMFORT mode heating times can be additionally activated.

The pellet burner start is in standby mode (ON) within the heating times (or 

always at deactivated heating times) and if the desired room temperature is 

below the actual room temperature.

The pellet burner stop either outside the heating periods, or if the desired room 

temperature is higher than the actual room temperature.

In the hibernation (OFF) no pellet burner start is possible, the system is turned 

off.

Pellet container refilling

Note

CAUTION when filling! Don’t allow the pellet bag to get in contact with the hot 

stove. Remove immediately pellets which have not found their way into the 

reservoir!

In order to prevent the fire from extinguishingt due to a lack of pellets, we 

recommend to keep an appropriate level in the reservoir upright. A 15 kg bag of 

pellets can be filled into your stove when half of the pellets the pellet container 

was consumed. See the level frequently. The container lid must, however, 

always be kept closed except when filling.

When filling the container during operation (opening the container lid) the fan 

starts up and pellet transport stops immediately, the operation will be resumed 

after closing the container lid (see WARNINGS AND ERROR MESSAGES)

Pellet container capacity (see SPECIFICATIONS).

Emergency operation - heating up without 

electrical Ignition

If the ignition cartridge fail, firelighters can be used for an emergency operation. 

First, start the stove as usual. Wait for the turning of the grid (only for units with 

turning grids). Then open the combustion chamber door and give a handful of 

pellets with the igniter into the cleaned burn pot, light up this and close the 

combustion chamber door.

Note

: Do not use flammable liquids to light up the fire!

Содержание Topo II

































Отзывы: