RIKA INTERNO, Руководство по эксплуатации GSM

Страница: 31 / 40

Stoves with Touchscreen
Command Input and Responses from Stove Software
Version 1.12/Touchscreen Software Version 1.22
(case insensitivity)
Start in the Manual Mode by specifying the heat output without
heating time:
for example:
1234 M70
Please note the space between the numerical
code and specification! The response (SMS reply)
reads: Manual Mode 70%
Start in the Automatic Mode by specifying the heat output with
heating times preassigned (If no heating times are stored , the stove
remains in standby)
for example:
1234 A70
The response (SMS reply) reads:
Automatic Mode 70 %, Heating Times Active
Start in the Comfort Mode by specifying the target room temperature
without heating times:
for example:
1234 C22
The response (SMS reply) reads:
Comfort Mode 22°C
Start in the Comfort Mode and specify the target room temperature
with heating times preassigned:
for example:
1234 CT22
The response (SMS reply) reads:
Comfort Mode 22°C, Heating Times Active
Switching off the pellet burner:
for example:
1234 OFF
The response (SMS reply) reads:
STOVE OFF
Frost Protection
It is possible to activate and deactivate the function frost protection
here:
for example:
1234 FON
The response (SMS reply) reads:
FROST PROTECTION ON
for example:
1234 FOFF
The response (SMS reply) reads:
FROST PROTECTION OFF
Operating parameter queries
Various set parameters are sent here (status, day heating times, actual
room temperature, etc.):
for example:
1234 ?
The response (SMS reply) reads:
Stove ON
AUTOMATIC MODE 65%
BURN OFF
HT1 ...
The current status, for example, could be: inactive, ignition, manual
mode, cleaning phase, etc.
HT1: Heating time 1 (if no heating time is set, 00:00 is displayed)
HT2: Heating time 2 (if no heating time is set, 00:00 is displayed)
RT: Actual room temperature (only with connected room sensor)
Warnings and Errors
If an error occurs during operation, the respective error is sent by
SMS message to the number saved last.
Important:
Not all warnings and errors occur in all stoves!
Please consult the manual of your stove for further informations.
Warnings / Errors Text-message
If the code text has an error
such as: 4213 A50
FAILURE: code error
If a wrong command was sent
(1234 bos).
FAILURE: text error
Resetting GSM module
(see notice below)
FAILURE: sending SMS - resetting
GSM module
There is no room sensor
connected. Please switch to
manual mode!
FAILURE: no room sensor
available
The room sensor lost the
connection during comfortmode
- please switch to manual mode!
WARNING: room sensor signal
lost - please switch to MANUAL
MODE
Pellet hopper lid open WARNING: pellet cover open
Door open WARNING: door open
Not enough low pressure
WARNING: not enough low
pressure
No pellets FAILURE: no pellets
Not ignited FAILURE: not ignited
Grid defect FAILURE: grid defect
Flame sensor defect FAILURE: flame sensor defect
Dischargemotor defect FAILURE: dischargemotor defect
Insertionmotor defect FAILURE: insertionmotor defect
Dischargemotor blocked FAILURE: dischargemotor blocked
Insertionmotor blocked FAILURE: insertionmotor blocked
Air flaps defect FAILURE: air flaps defect
Burnback flap FAILURE : burnback flap
Fan defect FAILURE: ID fan defect
Not enough low pressure
(permanent)
FAILURE: low pressure control
Stove overheated
FAILURE: safety temperature
limiter
Note:
Warning messages are not sent automatically. If during an SMS
request or command a warning message is on the display of the
stove, this warning is returned by SMS. For example as: Door open.
This is not possible when you suppress your telephone number!
Note:
If the modem is forced to send, for example through information
SMS of the network operator, SMS reply to a number, it will be
restarted for security reasons after five runs and sends a notification
to the stored number:
FAILURE: sending SMS - resetting GSM module
The modem is fully operating again after the automatic reboot.
| 31
EN
30