Rigol RSA Series Скачать руководство пользователя страница 64

Страница: 64 / 90

Chapter 2 Functions of the Front Panel

RIGOL

VNA User Guide

2-45

Input/Output

Sets the input/output interface.

Input Impedance

Sets the input impedance for voltage-to-power conversion. The default input

impedance is 5

0 Ω. To measure a 75 Ω device, you s

ould use a 75 Ω to 50 Ω adapter

(option) supplied by

RIGOL

to connect the analyzer with the system under test, and

then set the input impedance to 75 Ω.

Smith chart not only shows the reflection coefficient, but also the normalized

impedance. The impedance of the DUT can be obtained through the input

impedance. The formula for the normalized impedance is as follows:

Wherein, T

DUT

is the reflection coefficient.

When the input impedance is set to 50

, the impedance of the DUT is normalized

impedance * 50; when the input impedance is set to 75

, the impedance of the DUT

is normalized impedance * 75.

Ext Trig2

Sets

Ext Trig2

to "In" or "Out".

Shortcut Key

Preset

Recalls the preset setting and restores the system settings of the analyzer to a

specified status.

Remarks:

⚫

To set the preset type, press

System

→

Preset

→

Preset Type

to select

"Default" or any one of the items from "User1" to "User6".

⚫

Press

Preset

to recall the specified factory settings or user settings.

www.calcert.com

[email protected]

1.800.544.2843

Содержание RSA Series



























































































Результаты поиска

Содержание RSA Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol RSA Series, Руководство пользователя

Результаты поиска

Содержание RSA Series

Отзывы:

Бренды по названию

Популярные бренды