Rigol RSA Series Скачать руководство пользователя страница 63

Страница: 63 / 90

RIGOL

Chapter 2 Functions of the Front Panel

2-44

VNA User Guide

Peak

The peak search function enables the marker to move to the specific signal peak

point, and then in combination with the function of Delta marker, it can provide a

powerful analysis capability.

Peak Search

Performs the peak search function. Searches for the maximum value on the trace and

marks it with a marker.

Next Peak

Searches for and marks the peak whose amplitude on the trace is next to that of the

current peak and which meets the peak search condition.

Next Peak Right

Searches for and marks the nearest peak which is located at the right side of the

current peak and meets the peak search condition.

Next Peak Left

Searches for and mark the nearest peak which is located at the left side of the

current peak and meets the peak search condition.

Minimum Search

Searches for and marks the peak with the minimum amplitude on the trace.

Cont Peak

Enables or disables continuous peak search. By default, it is Off.

When it is enabled, after finishing each sweep, the analyzer will automatically

execute one peak search operation to track the measurement signal.

Remarks:

When the Cont Peak function is on, if the current marker is off, set the marker to

Position mode, and then execute the peak search operation.

www.calcert.com

[email protected]

1.800.544.2843

Содержание RSA Series



























































































Результаты поиска

Содержание RSA Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol RSA Series, Руководство пользователя

Результаты поиска

Содержание RSA Series

Отзывы:

Бренды по названию

Популярные бренды