Rigol RSA Series Скачать руководство пользователя страница 28

Страница: 28 / 90

Chapter 2 Functions of the Front Panel

RIGOL

VNA User Guide

2-9

Smith

0.03 to 20

N/A

Polar

0.03 to 20

N/A

Expand Phase

1a to 100G

degree (°)

Positive Phase

1a to 100G

degree (°)

Return Loss (DTF)

100f to 100G

Log Mag(DTF)

100f to 100G

Lin Mag(DTF)

0.1

1a to 100G

N/A

Auto Scale

Auto adjusts the graticule scale of the currently selected trace and the reference

value to make it optimal for display and observation.

All Auto Scale

Auto adjusts the graticule scale of all displayed traces and the reference value to

make them optimal for display and observation.

Remarks:

⚫

Once you enable this function, the graticule scale and reference position of the

corresponding traces will be updated automatically.

⚫

The All Auto Scale function only affects the display effects, but unable to affect

the measurement results.

www.calcert.com

[email protected]

1.800.544.2843

Содержание RSA Series



























































































Результаты поиска

Содержание RSA Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol RSA Series, Руководство пользователя

Результаты поиска

Содержание RSA Series

Отзывы:

Бренды по названию

Популярные бренды