Ricoh SR4080 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 74

background image

• The pre-stack paper stopper is released about 40 mm after the 2nd sheet turns on the pre-stack

stopper sensor [F], and the two sheets of copy paper are sent to the stapler tray. All sheets after the
2nd sheet go to the stapler tray via the paper guide [E].

Jogger Unit Paper Positioning

In the staple mode, as every sheet of paper arrives in the jogger unit, it is vertically and horizontally
aligned, then the staple edge is pressed flat to ensure the edge of the stack is aligned correctly for
stapling.

• Vertical Paper Alignment: About 60 ms after the trailing edge of the copy passes the staple tray

entrance sensor [A], the positioning roller motor [B] is energized to push the positioning roller [C]
into contact with the paper.

• The positioning roller and alignment brush roller [D] rotate to push the paper back and align the

trailing edge of the paper against the stack stopper [E].

• Horizontal Paper Alignment: When the print key is pressed, the jogger motor [F] turns on and the

jogger fences [G] move to the wait position about 7.2 mm wider than the selected paper size on
both sides.

• When the trailing edge of the paper passes the staple unit entrance sensor, the jogger motor moves

the jogger fences 3.7 mm towards the paper.

• Next, the jogger motor turns on again for 3.5 mm for the horizontal paper alignment then goes

back to the wait position.

• Paper Stack Correction: After the paper is aligned in the stapler tray, the left [J], center [K], and

right [L] stack plate motors switch on briefly and drive the front stack, center stack, and rear stack
plates against the edge of the stack to flatten the edge completely against the staple tray for
stapling.

• When the next copy paper turns on the stapler entrance sensor, the stack plate motor turns on and

returns to its home position. The home position is detected by stack plate HP sensor [M].

2. Detailed Descriptions

54

«
...
54
55
56
57
58
...
»

Содержание SR4080











































































Отзывы:

Нет отзывов

Похожие инструкции для SR4080

Бренд: Samsung Страницы: 2

Бренд: TallyGenicom Страницы: 175

Бренд: Fastjet Страницы: 52

Бренд: Oki Страницы: 48

Бренд: Oki Страницы: 34

Бренд: Oki Страницы: 65

Бренд: Oki Страницы: 44

Бренд: Oki Страницы: 36

Бренд: OHAUS Страницы: 28

Бренд: Oce Страницы: 396

Бренд: Oce Страницы: 28

Бренд: Oki Страницы: 64

Бренд: Keeler Страницы: 25

Бренд: TallyGenicom Страницы: 2

Liquid Crystal Opus

Бренд: PhotoCentric Страницы: 12

Бренд: TRAK Страницы: 98

5550N - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 16

SpeedSetter 300

Бренд: Xante Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды