Ricoh SR4080 Скачать руководство пользователя страница 55

Страница: 55 / 74

Solenoid/Gate

Selected Operation Mode

Upper Tray

Sort/Stack

Staple

[A]

Stapler junction gate solenoid

Off

[B]

Stapler junction gate

Closed

OPEN

[C]

Tray junction gate solenoid

Off

[D]

Tray junction gate

OPEN

Closed

Paper Pre-Stacking

• This mechanism improves productivity in staple mode. It is only used when copying on A4, LT, or

B5 (all LEF).

• During stapling, the copier has to wait. This mechanism reduces the wait by holding the first two

sheets of a job while the previous job is still being stapled. It only works during the second and
subsequent sets of a multi-set copy job.

• The pre-stack junction gate solenoid [A] turns on 120 mm after the 1st sheet of paper turns on the

entrance sensor, and this directs the sheet to the pre-stack tray [B]. (This sheet cannot be fed to the
stapler yet, because the first set is still being stapled.)

• The pre-stack paper stopper solenoid [C] turns on 350 mm after the 1st sheet turns on the entrance

sensor. The pre-stack paper stopper [D] then stops the paper.

• The pre-stack junction gate solenoid turns off 230 mm after the trailing edge of the 1st sheet passes

through the entrance sensor, and the 2nd sheet is sent to the paper guide [E].

Main Mechanisms

Содержание SR4080











































































Результаты поиска

Содержание SR4080

Отзывы:

Похожие инструкции для SR4080

Бренды по названию

Популярные бренды

Ricoh SR4080, Руководство по обслуживанию на месте

Результаты поиска

Содержание SR4080

Отзывы:

Похожие инструкции для SR4080

Бренды по названию

Популярные бренды