Ricoh Soleil-PJ WX4130 Скачать руководство пользователя страница 75

Страница: 75 / 100

Error

Meaning

Cause

Solution

Temp error

• The temperature around

the intake fan is 42
degrees C or higher.

• Temperature sensor is

defective.

• Check the environment, e.g.

whether there is any heat
source near the projector.

• Check if the temperature sensor

connector (CN10) is properly
connected.

• Replace the temperature sensor

board.

• Replace the main board.

Installation error

The projector is tilted at angle of
30 degrees or more.

• Check the projector condition.
• Check if the control panel

connector is properly
connected.

Memory read
error

A data access error occurred
while accessing the EEPROM
on the main board.

Replace the main board.

Audio processor
error

A data access error occurred
while accessing the audio
device.

Replace the main board.

Video processor
error

A data access error occurred
while accessing the video
decoder.

Replace the main board.

A/D converter
error

A data access error occurred
while accessing the A/D
converter.

Replace the main board.

HDMI receiver
error

A data access error occurred
while accessing the HDMI
receiver.

Replace the main board.

Error ID

Содержание Soleil-PJ WX4130





































































































Результаты поиска

Содержание Soleil-PJ WX4130

Отзывы:

Похожие инструкции для Soleil-PJ WX4130

Бренды по названию

Популярные бренды

Ricoh Soleil-PJ WX4130, Руководство по обслуживанию на месте

Результаты поиска

Содержание Soleil-PJ WX4130

Отзывы:

Похожие инструкции для Soleil-PJ WX4130

Бренды по названию

Популярные бренды