Ricoh LD013 Скачать руководство пользователя страница 223

Страница: 223 / 513

LASER EXPOSURE

B039/B040/B043

6-30

6.6 LASER

EXPOSURE

6.6.1 OVERVIEW

[A]: LD unit
[B]: Synchronization detector lens
[C]: Double toroidal lens
[D]: Shield glass
[E]: OPC drum
[F]: 1st mirror

[G]: 2nd mirror
[H]: F-theta lens
[I]: Polygon

mirror

[J]: Cylindrical

lens

[K]: Synchronization detector mirror

•

The LD drive board controls both the laser output and laser synchronization

mechanism.

•

The machine cuts off the power supply to the LD drive board if the front or right

cover is opened.

B039D101.WMF

[E]

[A]

[B]

[C]

[D]

[K]

[J]

[I]

[H]

[G]

[F]

Содержание LD013


































































































































































































































































































































































































































































































































Результаты поиска

Содержание LD013

Отзывы:

Бренды по названию

Популярные бренды

Ricoh LD013, Руководство по обслуживанию

Результаты поиска

Содержание LD013

Отзывы:

Бренды по названию

Популярные бренды