manualshive.com logo in svg

Ricoh LD013, Руководство по обслуживанию

Поделиться
Скачать
Ricoh LD013 Скачать руководство пользователя страница 133

T

rouble

-

s

hooting

SERVICE CALL CONDITIONS

SM

4-7

B039/B040/B043

No.

Definition

Symptom

Possible Cause

IMB non-connected error

925

B

IMB is not connected. This SC only
appears with B040 and B043 version
machines.

•

 IMB is not connected

•

 Poor connection between BiCU and

IMB

•

 IMB defective

•

 BiCU defective

Memory capacity error

926

B

The machine detects a discrepancy
between the memory capacity detected
during the memory check at power on
and the check at recovery from low
power or night/off mode.

•

 Poor connection between optional

DRAM and IMB

•

 Optional DRAM defective

•

 IMB defective

•

 BiCU defective

NVRAM error

981

B

The machine detects a discrepancy in
the NVRAM write/read data when
attempting to save actual data to the
NVRAM (i.e. during actual use).

•

 NVRAM defective

•

 Poor connection between BiCU and

NVRAM

•

 NVRAM is not connected

•

 BiCU defective

Communication error between BICU and IOB

990

B

The BiCU board cannot communicate
with the IOB.

•

 The connection between the BiCU

board and the IOB is poor.

•

 BiCU board defective

•

 IOB defective

Program version error

999

B

An incorrect type of main software was
downloaded.

•

 The main software for another

machine was downloaded to this
machine. Switch the machine off.
Connect an IC card that has the
correct firmware to the machine.
Switch the machine on, and download
the firmware. (

☛

 5.1.9)

Содержание LD013


































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды