Ricoh 161 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 192

background image

Transmission Modes

19

1

Parallel Memory Transmission

This function dials while the original is being scanned.
Standard Memory Transmission stores the original in memory, then dials the
destination. However, Parallel Memory Transmission allows you to confirm the
connection status quickly. In addition, this function scans the original faster than
Immediate Transmission. This is useful when you are in a hurry and need to use
the original for another purpose.

Important

❒

Standard Memory Transmission is used instead of Parallel Memory Trans-
mission in the following cases:
• When the line is busy and could not be connected to
• With Send Later
• When you store an original for Memory Transmission while another com-

munication is in progress

• When two or more destinations are specified
• When an original is placed on the exposure glass, and then sent

Note

❒

You can turn this function on or off with the User Parameters (switch 07, bit 2)
in the Fax Features menu.

❒

Standard Memory Transmission may be used instead of Parallel Memory
Transmission if there is not enough free memory left.

❒

If you use this function, the Memory Storage Report will not be printed.

❒

If the

{

Clear/Stop

}

key is pressed, the original jams or memory runs out, Par-

allel Memory Transmission will stop. The Communication Result Report is
printed and files are deleted.

❒

When using Parallel Memory Transmission, only the page number is printed
on the header of the fax, the total number of originals is not automatically
printed.

Reference

“Fax Features”, General Settings Guide

Automatic Redial

If a fax document could not be sent because the line was busy or an error oc-
curred during transmission, redial is attempted at five-minute intervals up to
five times.
If redialing fails after four redials, the machine cancels the transmission and
prints a Communication Result Report or Communication Failure Report.

Note

❒

If there are a large number of files stored in memory, documents might not be
sent in the order they were scanned.

«
...
25
26
27
28
29
...
»

Содержание 161

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 161

Бренд: Xyron Страницы: 6

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 40

Бренд: Xerox Страницы: 69

Бренд: Xerox Страницы: 42

Бренд: Dascom Страницы: 138

Бренд: Dascom Страницы: 166

ZINK PANPRINT01

Бренд: Pandigital Страницы: 2

Бренд: Xerox Страницы: 13

Бренд: Xerox Страницы: 16

Бренд: Lanier Страницы: 298

6130N - Phaser Color Laser Printer

Бренд: Xerox Страницы: 2

Бренд: Oki Страницы: 20

Бренд: Xerox Страницы: 5

Бренд: Ricoh Страницы: 682

ECOSYS M8124cidn

Бренд: Kyocera Страницы: 44

Бренд: Ricoh Страницы: 278

Бренд: UVP Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды