Richmond GTR156 Скачать руководство пользователя страница 23

Страница: 23 / 28

Revision 28

J2 Terminal:

(as per fig 17)

Terminal 1:

Optional External Close Push Button Switch.

Terminal 2:

Optional External Open Push Button Switch.

Terminal 3:

Optional External Stop Push Button Switch.

Terminal 4:

Common Terminal for All Optional Push Buttons.

(Hard-Wired keypad connection between terminals 4 & 5)

Terminal 5:

Optional External Open/Stop/Close Single Push Button

(does the 3 open/stop/close functions)

Terminal 6:

Optional External Push Button Pedestrian Switch

J5 Terminal

: Limit Switch and Accessories

Additional accessories sold separately

Terminal 7:

Power supply for accessories of J5 (+15V)

Terminal 8:

Photocell input (Normally Closed). If no photocell

is fitted use jumper between terminals 8 & 9.

Terminal 9:

Ground/Earth (GND)

Terminal 10:

Exit wand connection between terminals 9 & 10

Terminals 11, 12, and 13 are factory fitted (pre-wired)

Terminal 11:

Close spring limit switch

Terminal 12:

Spring limit switch common terminal

Terminal 13:

Open spring limit switch

Connecting Wires to the Terminal:

Using a screwdriver,

loosen the screw on the

side of the terminal.

Insert the wire into the

number on the terminal

that you are looking to

connect to. Refer to

Pages 20 & 21

Tighten with a

screwdriver to secure

the wire in place.

Содержание GTR156





























Результаты поиска

Содержание GTR156

Отзывы:

Похожие инструкции для GTR156

Бренды по названию

Популярные бренды

Richmond GTR156, Руководство пользователя

Результаты поиска

Содержание GTR156

Отзывы:

Похожие инструкции для GTR156

Бренды по названию

Популярные бренды