RIB KS2 12-24V, Руководство по сборке

Страница: 17 / 32

BC07049
Pag. 17 di 32
4 - CONNECTIONS
J1 => AERIAL Radio antenna
COM Common contact unit
PHOT.1 NC Photocell contact (NC)
STOP Stop button contact (NC)
OPEN Opening button contact (NO)
CLOSE Closing button contact (NO)
K BUTT. Single pulse contact (NO)
A+D+ Positive for accesories supply:
24Vdc for type KS2 PRINCE, 12Vdc for type KS2 KING
A-D- Negative for accessories supply:
24Vdc for type KS2 PRINCE, 12Vdc for type KS2 KING
Wiring of flasher
24Vdc (code ACG7061) for type KS2 PRINCE (
follow the
polarity )
12Vdc (code ACG7057) for type KS2 KING ( follow the
polarity )
SIGNAL BATTERY Wiring battery status led (12Vdc)
SIGNAL
Lamp gate open (12Vdc 3W max)
SIREN Wiring intrusion alarm siren (12Vdc max 300mA)
BUZZER Wiring acoustic warning (12Vdc max 200 mA)
LOCK Electric lock connection (Max 15W 12V)
J2 => BATTERY CHARGER Connector for battery charge card,
for type KS2 PRINCE, 24Vdc (code ACG4648)
for type KS2 KING, 12Vdc (code ACG4645)
J3 => EXP. 12V Connector for EXPANDER card (code ACG5471)
J4 => RADIO Connector for radio receiver, supply
24Vdc for type KS2 PRINCE - 12Vdc for type KS2 KING
J5 => MOTOR 1 Wiring MOTOR 1 (no polarity)
MOTOR 2 Wiring MOTOR 2 (no polarity)
J6 => SEC.TRANSF. Connector for transformer secondary
J7 => ENCODER Connection block for wiring of ENCODER M1and M2
S-M1 - Signal ENCODER M1
+ M1 - Positive supply ENCODER M1
GND - Negative supply ENCODER M1 and M2
+ M2 - Positive supply ENCODER M2
S-M2 - Signal ENCODER M2
J8 => SW Connector for factory encoding.
Do not alter the position of the jumper located as shown in figure
JP5 => Verify that the jumper is inserted !
J9 => L1 - N Supply 230 Vac 50/60 Hz (external to the card)
OPERATING MICROSWITCH
DIP 1 Checking the rotation direction of the motor (ON)
DIP 2 Timing (ON)
DIP 3 Pause time before the automatic closing (ON)
DIP 4 Jogging radio receiver (OFF) - automatic (ON)
DIP 5 Single impulse command (K BUTT) jogging (OFF) - automatic (ON)
DIP 6 Photocells always active (OFF) - Photocells active only on closure (ON)
DIP 7 Encoder enable (ON-active). Current sensor enable (OFF-active)
DIP 8 Pre-blinking (ON) - Normal blinking (OFF)
DIP 9 Pause time before the automatic pedestrian closing (ON)
DIP 10 Enable unlock stroke of electric lock (ON-active)
DIP 11 Enable electric lock (ON-active)
DIP 12 Selection of gear motor under use, PRINCE (ON) KING (OFF)
S1 => "PROG." Programming button
JP1 => selection of motor type for operation with current sensor M1
JP2 => selection of motor type for operation with current sensor M2
JP3 => selection of operation with 1 or 2 motors (default closed loop 2 motors)
LS => LOW SPEED - Electronic regulator for low speed
Adjustment of low speed is performed through the LOW SPEED trimmer, changing the
output voltage at the contacts of the motor or motors (turning clockwise the speed
increases). The adjustment is performed to set the correct speed for opening and closing
end travel, according the gate structure or presence of minor friction that could impair the
correct operation of the system.
M1 => Current sensor regulator for motor 1
M2 => Current sensor regulator for motor 2
LED SIGNALS
DL1 contact photocells (NC)
DL2 contact stop (NC)
DL3 control operation of current sensor M2
DL4 control operation of current sensor M1
DL5 control Encoder operation M2
DL6 control Encoder operation M1
DL7 programming activated
DL8 gate open M1 (green)
DL9 gate close M1 (red)
DL10 gate close M2 (red)
DL11 gate open M2 (green)
E
N
G
L
I
S
H
ELECTRONIC BOARD KS 2 12-24