9
How to Change REGISTER 1:
Vehicle Set Up:
A
LL
D
OORS
CLOSED
AND
T
HE
I
GNITION
T
URNED
O
N
L
AST
Remote Key
action:
T
URN
O
N
/
O
FF
F
EATURES
V
IA
T
HE
B
UTTON
O
N
T
HE
R
EMOTE
FEATURE
Press
Remote
This Many
Times
FACTORY
SETTING
DESCRIPTION
Arming & Disarming Beeps
1
ON
1 beep on Arm & 2 beeps on Disarm.
Door Lock on Ignition
(Anti-Hijack)
3
OFF
When this feature is on, the doors will lock when the ignition is
turned to on, and unlock when the ignition is turned to off.
No Door Ajar Warning
4
OFF
When this feature is on, the door ajar warning feature is
removed (the siren & indicators will not beep & flash for 3 sec. if
a door is not closed properly).
Perimeter Night Light
5
OFF
When this feature is on, the indicators will stay on constantly for
20 seconds on disarm, or until the ignition is turned on. This
allows for illumination around the vehicle at night.
Instant Boot Release
6
OFF
When this feature is on, the boot release button (Left Button)
will only require be pressing once rather than holding down for
3 seconds to open an electric boot.
Dome Light Extension
(Interior lights on when ignition
off, interior lights on when
system disarmed via remote).
Note:
This feature cannot be
turned on if Auto-Rearm &
Relock is activated. See
register 2.
8
OFF
The dome (interior) light comes on automatically when the
system is disarmed via remote, enabling the owner to verify the
vehicle is safe inside. The light stays on for 20 seconds, or until
the ignition is turned on. The dome (interior) light also comes on
automatically when the ignition is turned off, enabling the owner
to quickly gather belongings before exiting the car. The light
stays on for 20 seconds, or until the system is armed via
remote, or until the ignition is turned on again.
Upgrade Learn Mode
Used when you have no wiring
diagram for a specific vehicle.
It will allow the alarm to ‘learn’
the vehicles wires that will
change state on arm/disarm
from the factory remote.
9
OFF
Activating this feature will put the Upgrade interface into learn
mode. This is the alarm to learn the arm and disarm states of
wires POS1 / POS2, NEG1/NEG2, M1/M2.
Start with the car doors closed and the doors locked using the
factory remote. Please see “Factory Remote Interface: Learn
Mode” for more information.
Inhibit / Enable Mode
Selection for Upgrade inputs
10
Inhibit
Inhibit mode – NEG1 and NEG2 become inhibit wires which stop
the upgrade interface from arming/disarming the alarm i.e.
usually connects to the motor switch wires so that when they
open the door with the lock manually it will NOT disarm the
alarm
Enable mode – POS2 input becomes an ‘enable’ wire which
must go positive to allow the upgrade interface to arm/disarm
the system. This is usually connected to the blinkers, as they will
activate when the factor remote is pressed only.
NOTE: Enable mode POS2 wire in Upgrade Learnt mode will
learn the required state.
Shock Sensor Adjustment
11
6
SELECT
the level
required.
After pressing the remote 11 times to enter this mode, turn the
ignition to off. There are 8 levels of adjustment. The factory
default setting is level 6. Pressing the remote once will increase
the sensitivity by one level i.e. to level 7. The LED will then flash
seven times to confirm the new level. Pressing the remote again
will increase the sensitivity to level 8 (max). Pressing the remote
again will return the adjustment to level 1(least sensitive). Once
you have adjusted the sensitivity level to the desired setting, turn
the ignition on to exit this mode.
Installer Mode
12
SELECT
The Mode
Required
After pressing the remote 12 times to enter this mode, turn the
ignition to off. This mode allows the installer / owner to verify
that each trigger of the alarm system is working, without having
to arm & disarm the system each time & set off the siren. The
siren will beep and the blinkers will flash to indicate a trigger eg
push the bonnet switch, open a door, hit the vehicle. The siren
will beep four times to indicate a pre-warning impact sensor
detection, or once to indicate full alarm trigger level. Turn the
ignition to on to exit this mode.
