background image

ii

15

ii

To help you make informed decisions about safety, you 

will find important safety information in a variety of forms, 

including:
 

•  Safety Labels on the post driver and accessories. 

 

•  Safety Messages Preceded by a safety alert 

  

symbol and one of three signal words, DANGER, 

 

  WARNING, or CAUTION. These signal words mean:

 

    

Immediate hazards that will result in  

 

   

severe personal injury or death.

 

    

Hazards or unsafe practices that could  

 

   

result in personal injury.

 

    

Hazards or unsafe practices that could 

 

   

result in injury, product or property 

 

   

damage.

 

 

•  Safety Headings such as IMPORTANT SAFETY 

 

  INFORMATION.

 

•  Safety Section such as POST DRIVER SAFETY.

 

•  Instructions how to use this post driver correctly 

 

  and safely.

TAKE SAFETY SERIOUSLY

TROUBLE SHOOTING

15

© 2013, 2015 Rhino Tool Company Inc., - All Rights Reserved

Your safety, and the safety of others, 

is very important. The proper and safe 

use of your Rhino

® 

post driver and 

accessories is an important responsi-

bility and should be taken seriously.  

 

Keep this owner’s manual available, 

so you can refer to it at any time. 

This owner’s manual is considered a 

permanent part of the post driver and 

accessory and should remain with the 

post driver and accessory if resold. 

The information and specifications 

included in this publication were 

in effect at the time of approval 

for printing. Rhino Tool Company, 

Inc. reserves the right, however, to 

discontinue or change specifications 

or design at any time without notice 

and without incurring any obligation 

whatever. No part of this publication 

may be reproduced without written 

permission from: 

 

Rhino Tool Company

Your safety, and the safety of others, 

is very important. The proper and safe 

use of your Rhino

® 

post driver and 

accessories is an important responsi-

bility and should be taken seriously.  

 

Keep this owner’s manual available, 

so you can refer to it at any time. 

This owner’s manual is considered a 

permanent part of the post driver and 

accessory and should remain with the 

post driver and accessory if resold. 

The information and specifications 

included in this publication were 

in effect at the time of approval 

for printing. Rhino Tool Company, 

Inc. reserves the right, however, to 

discontinue or change specifications 

or design at any time without notice 

and without incurring any obligation 

whatever. No part of this publication 

may be reproduced without written 

permission from: 

 

Rhino Tool Company

!

WARNING

!

DANGER

!

CAUTION

IMPORTANT

NOTE

!

WARNING

!

DANGER

!

CAUTION

IMPORTANT

NOTE

!

WARNING

!

DANGER

!

CAUTION

IMPORTANT

NOTE

This book contains important safety information. 

Please read it carefully.

Call your local dealer, service center or Rhino Tool 

Company for more assistance with your post driver

i

To help you make informed decisions about safety, you 

will find important safety information in a variety of forms, 

including:
 

•  Safety Labels on the post driver 

 

•  Safety Messages Preceded by a safety alert 

  

symbol and one of three signal words, DANGER, 

 

  WARNING, or CAUTION. These signal words mean:

 

    

Immediate hazards that will result in  

 

   

severe personal injury or death.

 

    

Hazards or unsafe practices that could  

 

   

result in personal injury.

 

    

Hazards or unsafe practices that could 

 

   

result in injury, product or property 

 

   

damage.

 

 

•  Safety Headings such as IMPORTANT SAFETY 

 

  INFORMATION.

 

•  Safety Section such as POST DRIVER SAFETY.

 

•  Instructions how to use this post driver correctly 

 

  and safely.

TAKE SAFETY SERIOUSLY

TROUBLE SHOOTING

© 2013, 2015 Rhino Tool Company Inc., - All Rights Reserved

!

WARNING

!

DANGER

!

CAUTION

IMPORTANT

NOTE

!

WARNING

!

DANGER

!

CAUTION

IMPORTANT

NOTE

!

WARNING

!

DANGER

!

CAUTION

IMPORTANT

NOTE

This book contains important safety information. 

Please read it carefully.

Call your local dealer, service center or Rhino Tool 

Company for more assistance with your post driver

Symptom

Explanation/Procedure

Post lodged in the 

driver

1. Remove the 2 bolts that secure the adapter and separate the driver from the adapter.

2. Slide the adapter down the post to expose the top of the post. With the proper cutting tool for the type of post, cut 

through the post below the flared portion. 

3. Once the deformed portion is removed, slide the adapter off the post and reassemble it to the driver. Please follow 

bolt tightening procedure.

Drives post slow  

or sluggish 

performance

1. Inspect the chuck to see if there is any foreign material blocking the piston.

2. Check to see if piston is moving freely by disconnecting the driver from air, tipping upside down and back upright. 

You should be able to hear the piston moving freely.

3. Check to ensure the rate of lubrication is adequate.

4. If using a FRL, inspect the filter on the FRL, if impacted with residue replace with new filter.

5. Inspect the filter on the Throttle. If clogged, blow off debris with air hose, or clean with a common cleaning solvent.

6. Check to see if air pressure is correct

7. Check output on compressor

8. In temperatures under 40ºF (4ºC) or high humidity conditions check air lines and tool for icing.

Noticeable air passing 

through driver or 

“blow by”

To confirm this condition exists, connected to air source, place driver on a post, while activating the throttle lift the 

driver slightly if the piston increases in activity blow by is confirmed. This indicates there is most likely damaged or 

worn parts inside the driver. In this event the driver should be sent to Rhino Tool Company to be inspected and we 

will report if the driver is repairable.

Other problems or 

technical questions

Other problems or technical questions: Document your serial number and contact Rhino Tool Company. Phone: 

309.853.5555 or Toll Free 866-707-1808, Fax:309.856.5905, Email: [email protected]. In Europe contact Eurogate Int. 

F: (0031) (0) 523 638286, M: (0031) (0) 610 502607.

Symptom

Explanation/Procedure

Post lodged in the 

driver

1. Remove the 2 bolts that secure the adapter and separate the driver from the adapter.

2. Slide the adapter down the post to expose the top of the post. With the proper cutting tool for the type of post, cut 

through the post below the flared portion. 

3. Once the deformed portion is removed, slide the adapter off the post and reassemble it to the driver. Please follow 

bolt tightening procedure.

Drives post slow  

or sluggish 

performance

1. Inspect the chuck to see if there is any foreign material blocking the piston.

2. Check to see if piston is moving freely by disconnecting the driver from air, tipping upside down and back upright. 

You should be able to hear the piston moving freely.

3. Check to ensure the rate of lubrication is adequate.

4. If using a FRL, inspect the filter on the FRL, if impacted with residue replace with new filter.

5. Inspect the filter on the Throttle. If clogged, blow off debris with air hose, or clean with a common cleaning solvent.

6. Check to see if air pressure is correct

7. Check output on compressor

8. In temperatures under 40ºF (4ºC) or high humidity conditions check air lines and tool for icing.

Noticeable air passing 

through driver or 

“blow by”

To confirm this condition exists, connected to air source, place driver on a post, while activating the throttle lift the 

driver slightly if the piston increases in activity blow by is confirmed. This indicates there is most likely damaged or 

worn parts inside the driver. In this event the driver should be sent to Rhino Tool Company to be inspected and we 

will report if the driver is repairable.

Other problems or 

technical questions

Other problems or technical questions: Document your serial number and contact Rhino Tool Company. Phone: 

309.853.5555 or Toll Free 866-707-1808, Fax:309.856.5905, Email: [email protected]. In Europe contact Eurogate Int. 

F: (0031) (0) 523 638286, M: (0031) (0) 610 502607.

21

Содержание Pro Series 301250

























Отзывы: