RHINO Multi-Pro 301002 Скачать руководство пользователя

Страница: 5 / 32

The Rhino

Multi-Pro

™

gas powered

driver is designed to drive fence post,

ground rod, delineator post, vineyard post,

form pin, tent stake and other like items

into the ground.

Uses, other than those

intended, can result

in injury to the operator as well as those

around the operator. Damage to the driver

and to the surrounding area may result

as well. This post driver is intended for

use by professional installers. Never allow

children to operate this tool.
Most accidents can be prevented if you

follow all instructions in this manual and

on the post driver. The most common haz-

ards are discussed below, along with the

best method to protect yourself and others.

UNDERGROUND

UTILITIES:

Driving

a post into an underground utility can be

EXTREMELY DANGEROUS

, exposing

the operator and those around to poten-

tially life threatening danger. Damage to

surrounding property can also occur as a

result of a post being driven into an under-

ground utility. Be absolutely certain that

you are aware of all underground utilities

in the area in which you intend to drive

posts. Ensure that a certified locating ser

vice has identified all underground utilities

prior to beginning your project. Failure to

do so can be catastrophic. Underground

utilities include but are not limited to:

Electric, Gas, Telephone, Water, Sewer,

TV Cable, Lawn Sprinklers, etc.

GASOLINE

: Gasoline

is HIGHLY

FLAMMABLE and EXPLOSIVE. You

can be burned or seriously injured when

handling fuel.

EXHAUST

: The ex-

haust from the engine

contains poisonous carbon monoxide gas

that can build up to dangerous levels in

closed areas. Breathing carbon monoxide

can cause unconsciousness or death. Never

run the engine in a closed or even partly

closed area where people may be present.

The engine exhaust

from this product contains chemicals

known to the State of California to cause

cancer, birth defects or other reproductive

harm.

ENGINE

MAINTENANCE:

Improperly maintaining the engine on this

power tool, or failure to correct a problem

before operation, can cause a malfunc-

tion in which you can be seriously hurt

or killed. In accordance with the engine

owner’s manual, always perform a pre-

operation inspection of the engine before

each use and correct any problem.

DRIVER

MAINTENANCE

Improperly maintaining the driving

mechanism on this power tool, or failure

to correct a problem before operation, can

cause a malfunction in which you can be

seriously hurt or killed.
In accordance with this manual, always

perform a pre-operation inspection of the

driving mechanism before each use and

correct any problem.

IMPORTANT SAFETY INFORMATION

POST DRIVER SAFETY

WARNING

DANGER

CAUTION

IMPORTANT

NOTE

WARNING

DANGER

CAUTION

IMPORTANT

NOTE

WARNING

DANGER

CAUTION

IMPORTANT

NOTE

WARNING

DANGER

CAUTION

IMPORTANT

NOTE

WARNING

DANGER

CAUTION

IMPORTANT

NOTE

WARNING

DANGER

CAUTION

IMPORTANT

NOTE

WARNING

DANGER

CAUTION

IMPORTANT

NOTE

Содержание Multi-Pro 301002

































Результаты поиска

Содержание Multi-Pro 301002

Отзывы:

Похожие инструкции для Multi-Pro 301002

Бренды по названию

Популярные бренды

RHINO Multi-Pro 301002, Руководство пользователя

Результаты поиска

Содержание Multi-Pro 301002

Отзывы:

Похожие инструкции для Multi-Pro 301002

Бренды по названию

Популярные бренды