background image

Safety Section  1-3

SAFETY

© 

2005 

Alamo Group Inc.

SAFETY

7600A   06/05

Si no lee Ingles, pida ayuda a alguien que si lo lea para que le
traduzca las medidas de seguridad. 

(SG-3)

PELIGRO!

!LEA EL INSTRUCTIVO!

WARNING!

Engine Exhaust, some of its constituents, and certain vehicle
components contain or emit chemicals known to the state of California
to cause cancer and birth defects or other reproductive harm.  (SG-30)

WARNING!

Battery posts, terminals and related accessories contain lead and lead
compounds, chemicals known to the state of California to cause
cancer and birth defects or other reproductive harm. Wash Hands after
handling.  (SG-31)

Operator Safety Instructions and Practices

WARNING!

The rotating parts of this machine continue to rotate even after the PTO
has been turned off.  The operator should remain in his seat for 60
seconds after the brake has been set, the PTO disengaged, the tractor
turned off, and all evidence of rotation has ceased.            

(S3PT-10)

 “Wait a minute...Save a life!”

DANGER!

Never crawl under a raised Implement supported solely  by the Tractor 3-
Point hitch.  Release of the control lever or mechanical failure will result
in the Implement falling and possible injury or death.  Always securely
block up the Implement before crawling underneath to perform repairs and
service. 

 (S3PT-19)

DANGER!

Never operate the Tractor or Implement until you have read and
completely understand this Manual, the Tractor Operator’s  Manual,
and each of the Safety Messages found in the Manual or on the Tractor
and Implement.  Learn how to stop the tractor engine suddenly in an
emergency

  Never allow inexperienced or untrained personnel too

operate the Tractor and Implement without supervision.

      

Make sure

the operator has fully read and understood the manuals prior to
operation.

 

 

(SG-4)

WARNING!

The operator and all support personnel should wear hard hats,
safety shoes, safety glasses, and proper hearing protection at all
times for protection from injury including injury from items thrown by
the equipment. 

 (SG-16)

Содержание 5047C

















































































Отзывы: