Rhin-O-Tuff EWC-8370 Скачать руководство пользователя | Manualshive

Страница: 6 / 24

background image

983001 8370 EWC8370 8318 Issue May 2007

Page

4

Important Safety Notice!

Make sure you read this section very carefully! Learn to recognize this
Safety Alert Symbol. The EWC-8370 has been designed to provide a
very high level of protection to an operator. Follow the guidelines below
while installing, operating and maintaining your machine.

¾

Plug the EWC-8370 into an outlet that provides a 15-amp

service (16-amp for European installation) that is protected at
the customer’s circuit box (EWC-8370 only).

¾

Always replace fuses or circuit breakers with the correct

amperage and type.

¾

If the machine cycles erratically turn off and unplug, call dealer

immediately for service.

¾

Never bypass safety devices!

Special EWC-8370 Note:

This manual covers the HD-8370, EWC-8370, and the HC-8318 wire

closers. When this manual refers to the Upper Position of the closing bar, the
EWC-8370 is in the normal up position at rest. Then referring to pulling the
handle or closing wire, the EWC-8370 is operated with the two green buttons,
one on each side of the table. Both buttons must be pressed at the same time
for the machine to cycle.

«
...
4
5
6
7
8
...
»

Содержание EWC-8370

























Отзывы:

Нет отзывов

Похожие инструкции для EWC-8370

Бренд: ZOJE Страницы: 28

Бренд: Adler Страницы: 20

Бренд: Kärcher Страницы: 501

Бренд: Numatic Страницы: 52

Бренд: Janome Страницы: 22

Бренд: Sagem Страницы: 104

HAKOMATIC B 90 CL

Бренд: HAKO Страницы: 42

aerobic twisting stepper

Бренд: Brookstone Страницы: 14

Бренд: SunStar Страницы: 36

Бренд: Paitec Страницы: 21

Gigaset DX600A ISDN

Бренд: Siemens Страницы: 69

Бренд: HQ Power Страницы: 20

Saeco INCANTO HD8927/47

Бренд: Saeco Страницы: 76

GrabBaristo HD8964

Бренд: Saeco Страницы: 92

Бренд: BT Страницы: 63

Бренд: Atlanta Attachment Company Страницы: 90

ZJ-M6-GS800-SF-V2

Бренд: ZOJE Страницы: 31

Бренд: Euro-Pro Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды