background image

64

LIMITED PARTS WARRANTY 

HI DELTA – TYPES H AND WH 

MODELS 992C–2342C 

SCOPE

Raypak, Inc. (“Raypak”) warrants to the original owner that all parts of this heater which are actually manufactured by Raypak will be free 

from failure under normal use and service for the specified warranty periods and subject to the conditions set forth in this Warranty. Labor 

charges and other costs for parts removal or reinstallation, shipping and transportation are not covered by this Warranty but are the 

owner’s responsibility. 

HEAT EXCHANGER WARRANTY

Domestic Hot Water

Five (5) years from date of heater installation. Includes copper heat exchanger with bronze and cast iron waterways. 

Ten (10) years from date of heater installation. Includes only cupro-nickel heat exchanger with bronze or cast iron waterways. 

Space Heating (Closed Loop System)

Ten (10) years from date of heater installation. Includes both cupro-nickel and copper heat exchanger with bronze or cast iron water-

ways. 

Thermal Shock Warranty

Twenty (20) years from date of heater installation against “Thermal Shock” (excluded, however, if caused by heater operation at large 

changes exceeding 150°F between the water temperature at intake and heater temperature, or operating at heater temperatures exceed-

ing 230°F). 

ANY OTHER PART MANUFACTURED BY RAYPAK

One (1) year warranty from date of heater installation, or eighteen (18) months from date of factory shipment based on Raypak’s records, 

whichever comes first. 
SATISFACTORY PROOF OF INSTALLATION DATE, SUCH AS INSTALLER INVOICE, IS REQUIRED. THIS WARRANTY WILL BE 

VOID IF THE HEATER RATING PLATE IS ALTERED OR REMOVED. 

ADDITIONAL WARRANTY EXCLUSIONS

This warranty does not cover failures or malfunctions resulting from: 

1. Failure to properly install, operate or maintain the heater in accordance with our printed instructions provided; 

2. Abuse, alteration, accident, fire, flood and the like; 

3. Sediment or lime build-up, freezing, or other conditions causing inadequate water circulation; 

4. High velocity flow exceeding heater design rates; 

5. Failure of connected systems devices, such as pump or controller; 

6. Use of non-factory authorized accessories or other components in conjunction with the heater system; 

7. Failing to eliminate air from, or replenish water in, the connected water system; 

8. Chemical contamination of combustion air or use of chemical additives to water. 

PARTS REPLACEMENT

Under this Warranty, Raypak will furnish a replacement for any failed part. The failed part must first be returned to Raypak if requested, 

with transportation charges prepaid, and all applicable warranty conditions found satisfied. The replacement part will be warranted for 

only the unexpired portion of the original warranty. Raypak makes no warranty whatsoever on parts not manufactured by it, but Raypak 

will apply any such warranty as may be provided to it by the parts manufacturer. 

TO MAKE WARRANTY CLAIM

Promptly notify the original installer, supplying the model and serial numbers of the unit, date of installation and description of the prob-

lem. The installer must then notify his Raypak distributor for instructions regarding the claim. If either is not available, contact Service 

Manager, Raypak, Inc., 2151 Eastman Avenue, Oxnard, CA 93030 or call (805) 278-5300. In all cases proper authorization must first be 

received from Raypak before replacement of any part. 

EXCLUSIVE WARRANTY - LIMITATION OF LIABILITY

This is the only warranty given by Raypak. No one is authorized to make any other warranties on Raypak’s behalf. THIS WARRANTY IN 

LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MER-

CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. RAYPAK’S SOLE LIABILITY AND THE SOLE REMEDY AGAINST 

RAYPAK WITH RESPECT TO DEFECTIVE PARTS SHALL BE AS PROVIDED IN THIS WARRANTY. IT IS AGREED THAT RAYPAK 

SHALL HAVE NO LIABILITY, WHETHER UNDER THIS WARRANTY, OR IN CONTRACT, TORT, NEGLIGENCE OR OTHERWISE, 

FOR ANY SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGE, INCLUDING DAMAGE FROM WATER LEAKAGE. Some states 

do not allow limitations on how long an implied warranty lasts, or for the exclusion of incidental or consequential damages. So the above 

limitation or exclusion may not apply to you. 
This Limited Warranty gives you specific legal rights. You may also have other rights which may vary from state to state. We suggest that 

you complete the information below and retain this certificate in the event warranty service is needed. Reasonable proof of the effective 

date of the warranty (date of installation) must be presented, otherwise, the effective date will be based on the rate of manufacture plus 

thirty (30) days. 

Original Owner  

 

Model Number 

Mailing Address  

 

Serial Number 

 

 

Date of Installation 

City                                           State               Zip Code   

Installation Site 

Daytime Telephone Number 

 

Contractor/Installer 

RAYPAK, INC

 2151 Eastman Avenue   Oxnard, CA 93030-9786   (805) 278-5300   Fax (800) 872-9725   www.raypak.com 

Содержание Raypak Hi Delta 1262C









































































Отзывы: