background image

Connecting to a Nurse Call System 

NOTE: 

For the facility which has no nurse call system, 

the ST750 is very effective in alerting caregivers with 
Melody/Tone when a patient tries to leave the bed or 
room. 
Setting up the ST750 Control Unit is the same whether it 
is connected to a nurse call system or not. Please refer to 
pages 7-10 for details using different sensor types. 

There are a variety of nurse call systems made by 
various manufacturers. Ask your distributor for a proper 
connector to install the ST750. 

1.

Connect the ST750 to the existing nurse call
system's wall port using the connection cord (not
included) by inserting one end of the connection
cord into the ST750 nurse call jack and plugging
the other end into the existing nurse call system's
wall port.

161

Nurse call 

� 

connector 

-

Sensor 

$! 

0

When connecting the ST750 to the nurse call 
system: 

When ST750 receives the si

gn

al from

the sensor pad, it sends out the si

gn

al to

the staff room through the nurse call
system.

If the volume level is set to LIS, the
alarm will only sound at the nurse call
station, not in the patient's room.

ST750 Instruction Manual  (0510-0496-C) 

Selecting a Melody/Tone for the 

Alarm 

Slide the Melody/Tone switch to Melody mode. Melody 
starts and continues sounding when you press and hold 
the Sound select button. Release the button and then press 
the button again to listen to the next melody. Repeat until 
you decide which melody to use. 

Melody 

William Tell Overture

Jingle Bells

Turkish March

Fur Elise

The Lonely Shepherd

Long Long Ago

Voice Of Spring

Carmen Overture

Slide the Melody/Tone switch to Tone mode. Tone starts 
and continues beeping when you press and hold the 
Sound select button. Release the button and then press the 
button again to listen to the next tone. Repeat until you 
decide which tone to use. 

Tone 

Pi-Pi- Pi-Pi-

PuPi- PuPi-

PuPi-PuPi-PuPi-

PuPiPiPuPiPi

Pi--- Pi Pi

Pi Pi Pi Pi

PiPi- PiPi-

PiPiPi PiPiPi

To Turn Off the ST750 

1.

Press the Hold button.

2.

Unplug the sensor.

3.

The unit will tum off in 30 seconds.

¾ 

Dispose of Properly

-

If you no longer use the device or its accessories, 
dispose of according to the local regulations in force. 

Page  9  of 12 

Содержание Sensatec ST750













Отзывы: