Reznor RA 140 Скачать руководство пользователя страница 8

Страница: 8 / 52

Form I-RA/D 140/235 (Version A), Page 8

Heater

Placement

Do not attempt to install this heater until you have read and

understand this manual!

Placement is critical to the efficient operation of this heater.
Measure all distances to comply with the specific code requirements

and minimum clearances listed below.
Refer to the section on Venting your heater for vent requirements

and recommendations.
Locate the heater so that suitable means shall be provided to facili-

tate regular cleaning and maintenance of the heater (i.e. permanent

platform, portable stairs, ladder, etc.).

WARNING: You must comply with all requirements

on distance from heater to combustibles.

Fan Models

Blower Models

RA140/235

RAD140/235

inches

Top

152

Front

1219

Side

(Burner)*

Canada

152

United

States

457

Side

(Opposite

Burner)*

Canada

152

United

States

457

Rear*

610

152

Bottom

152

Flue Pipe

Canada

229

United

States

457

*Allow for service access.

In Canada, for additional information on installation clearances, refer

to CAN/CSA-B139-M91, “Installation Code for Oil Burning Equipment,”

Clause 7.0 - Installation Clearances.

WARNING: Clearances apply to all combustibles.

Do not leave paper, rags, or any moveable combus

tibles near the heater or store gasoline or any other

flammable fluid near this appliance.

Minimum

Clearances

from

Combustibles

Содержание RA 140





















































Результаты поиска

Содержание RA 140

Отзывы:

Похожие инструкции для RA 140

Бренды по названию

Популярные бренды

Reznor RA 140, Руководство по установке, эксплуатации и техническому обслуживанию и справочное руководство

Результаты поиска

Содержание RA 140

Отзывы:

Похожие инструкции для RA 140

Бренды по названию

Популярные бренды