Reznor RA 140 Скачать руководство пользователя страница 43

Страница: 43 / 52

Form I-RA/D 140/235 (Version A), Mfg No. 110318 Rev 4, Page 43

Troubleshooting

Continued

Chart No. 4 - Burner ignites and burns

steadily until the system goes into lockout.

NOTE:

If the flame goes

out during this test and the

burner continues to operate,

go to Chart No. 5.

1. Remove cad cell wires from the ignition controller.

2. Start the burner.

Jumper F-F terminals on the ignition controller.

Does ignition

controller

lockout?

Replace

ignition

controller.

Measure resistance across cell leads (F-F

terminals on the ignition controller).

Is resistance

zero?

Is resistance

greater than

1500 ohms?

Is the over fire

draft correct?

Is resistance

greater than

1500 ohms?

Is resistance

greater than

1500 ohms?

Is the CO2

correct?

Correct

short

circuit.

Cad cell

and

ignition

controller

are OK.

Open transformer

and clean cell face

and seat firmly into

holder.

Adjust for

proper CO2.

Replace the cad cell.

YES

Adjust barometric

pressure.

Содержание RA 140





















































Результаты поиска

Содержание RA 140

Отзывы:

Похожие инструкции для RA 140

Бренды по названию

Популярные бренды

Reznor RA 140, Руководство по установке, эксплуатации и техническому обслуживанию и справочное руководство

Результаты поиска

Содержание RA 140

Отзывы:

Похожие инструкции для RA 140

Бренды по названию

Популярные бренды