manualshive.com logo in svg

Reynolds Building Systems the Belmont-R, Руководство по сборке

Поделиться
Скачать
Reynolds Building Systems the Belmont-R Скачать руководство пользователя страница 16

1.

Install a 121-1/2" long 1x6 trim board at the rear of the building, flush with the face of the 2x4.

Install the 1x6 board so the face of the board is aligned with the top of the trusses. Use a straight
edge as shown below. Use 8d galv. nails.

Supplied in our component kit.

Cut a 72" to 48"

Step 19

Install Roof Sheathing

1.

Install 4x8 roof sheathing starting at the lower back corners. The bottom edge of the sheathing

should extend past the end of the trusses and rest on the 1x6 fascia. Make sure the trusses and
gables are plumb and the roof sheathing meets the center of the trusses.

2.

Install roof sheathing per layout below. The top row of sheathing is supplied in our component

kit. There will be a gap at the top to allow ventilation if ridge vent is applied. Insert (2) two
ply-clips into the roof sheathing between each truss at the top row, see drawing on next page.
Secure sheathing with 7d sinkers nails. Space nails 12" apart.

Air
Space

Step 18

Install 1x6 Fascia on Sidewalls

1x6 Fascia Board

Straight Edge

Optional ridge vent provides

ideal ventilation.

48" x 96"

48" x 96"

48" x 48"

48" x 96"

72"

48"

48" x 96"

48"

48" x 96"

48" x 48"

72"

48"

2.

Install a 1x6-8'  board.

3.

Cut 1x6-8'  board flush with the 2x4

on the front gable.

Содержание the Belmont-R





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды