REXON MS10W2 Скачать руководство пользователя страница 9

9

ENVIRONMENTAL PROTECTION

Waste electrical products should 

not be disposed of with household 

waste. Please recycle where 

facilities exist. Do not dispose 

of electrical appliances as unsorted 

municipal waste, use separate collection 

facilities. Contact your local government 

for information regarding the collection 

systems available. If electrical appliances 

hazardous substances can leak into the 

groundwater and get into the food chain, 

damaging your health and wellbeing. When 

replacing old appliances with new once, the 

retailer is legally obligated to take back your 

old appliance for disposal at least for free of 

charge. Disposal of discarded material shall 

be in accordance with local environmental 

regulations.

Installation

KNOW YOUR MITER SAW (FIG. 1)

1.  Switch handle

2.  Lower blade guard

3.  Hold-down clamp assembly

4.  Right extension wing

5.  Miter handle

6.  Table insert

7.  Base

8.  Left extension wing

9.  Sliding fence

10.  Motor

11.  Cover plate

12.  Belt cover

13.  Exhaust port

14.  Hold-down latch

15.  Bevel locking handle

16.  Mounting hole

17.  Extension wing locking knob

18.  Turntable

19.  Miter scale 

20.  Positive stop locking lever

21.  Blade

22.  Arbor lock

23.  ON/OFF Trigger switch

설  치

1. 

스위치 핸들
안전커버
작업물 고정 클램프
연결대-오른쪽
베이스 각도핸들
테이블 인서트
베이스
연결대-왼쪽
슬라이드 펜스
모터
톱날 보호덮개 
벨트커버
톱밥 배출구
헤드 잠금 걸쇠
베벨각도 고정핸들
연결대 고정 홈
연결대 고정 손잡이
테이블
각도 표시 눈금자
각도 고정 레버
톱날
스핀들 고정핀

ON/OFF

 스위치

2. 

3. 

4. 

5. 

6. 

7. 

8. 

9. 

10. 

11. 

12. 

13. 

14. 

15. 

16. 

17. 

18. 

19. 

20. 

21. 

22.  

23. 

각도절단기 부분 명칭

 (

그림

. 1)

환경보호

            폐 전기 제품은 가정 쓰레기와 함께
            처리하면 안됩니다. 재활용 센터를 
            통하여 재활용하십시오. 전기 제품을 
            분류되지 않은 일반 폐기물로 처리
하지 마십시오. 별도의 수거 시설을 사용하십
시오. 사용 가능한 수거 시스템에 관한 정보는 
지방 정부에 문의하십시오. 전기 제품이 매립
식 쓰레기 매립장에 버려지면 유해 물질이 
지하수로 누출되어 먹이 사슬로 빠져 건강과 
복지에 해를 끼칠 수 있습니다.

Содержание MS10W2





































Отзывы: