REXON MS10W2 Скачать руководство пользователя страница 4

4

General Safety Rules

Read all these instructions before 

attempting to operate your product. 

Save these instructions for future 

reference.

1. 

Keep work area clear.

 Cluttered areas 

and benches invite injuries.

2. 

Consider work area environment.

 

Do not expose tools to rain. Do not use 

tools in damp or wet locations. Keep 

work area well lit. Do not use tools in the 

3. 

Guard against electric shock.

 Avoid 

body contact with earthed or grounded 

surfaces.

4. 

Keep other people away.

 Do not let 

others, especially children, not involved 

in the work  touch the tool or the 

extension lead and keep them away 

from the work area.

5. 

Store idle tools.

 When not in use, tools 

should be stored in a dry locked-up 

place, out of reach of children.

6. 

Do not force the tool.

 It will do the job  

better and safer at the rate for which it 

was intended.

7. 

Use the right tool.

 Do not force small 

tools to do the job of a heavy duty 

tool. Do not use tools for purposes 

not intended; for example do not use 

circular saws to cut tree limbs or logs.

8. 

Dress properly.

 Do not wear loose 

clothing or jewellery, they can be caught 

in moving parts. Non-skid footwear is 

recommended when working outdoors. 

Wear protective hair covering to contain 

long hair. 

9. 

Use protective equipment.

 Use safety 

glasses. Use face or dust mask if cutting 

operations create dust.

WARNING ! When using electric tools 

basic safety precautions should always 

electric shock and personal injury.

일반안전규칙

경고! 전동 공구를 사용할 경우, 화재, 감전 및 

부상의 위험을 줄이기 위해 항상 기본 안전 

수칙을 준수해야 합니다.

제품을 사용하기전에  이 메뉴얼을 
모두 읽으십시오. 나중에 참조할 수 
있도록 이 메뉴얼을 보관하십시오.

작업 공간을 깨끗하게 유지하십시오.

 

어수선한 곳과 진열대는 부상을 초래합니다.

작업 공간 환경을 고려하십시오.

 기계를 비에

노출시키지 마십시오. 습기가 있거나 젖은
곳에서는 기계를 사용하지 마십시오.
작업 공간을 밝게 유지하십시오. 인화성 액체
또는 가스가 있는 곳에서 기계를 사용하지 
마십시오.

감전 방지

 접지된 표면과 신체 접촉을

피하십시오.

작업자외, 다른 사람들을 기계에서 멀리 떨어

지게 하십시오.

 작업에 관여하지 않은 다른

사람, 특히 어린이가 기계나 전선 등 기계에
연관된 부품에 손을 대지 않도록 하고 작업
공간에서 멀리 떨어지게 하십시오.

사용하지 않는 부품을 따로 보관하십시오.

 

기계를 사용하지 않을 때는 도구를 어린이의
손이 닿지 않는 건조하고 안전한 곳에 보관
해야 합니다.

부품을 억지로 조립하지 마십시오.

 그것이 

의도했던 속도로 더 잘하고 안전하게 작업
할 수 있게 할 것입니다.

작업 상황에 맞는 기계를 사용 하십시오.

 

작은 기계로 강력한 힘을 요하는  작업을 
하도록 강요하지 마십시오. 용도에 맞지
않는 공구를 사용하지 마십시오. 예를 들어
나뭇가지나 통나무를 자르기 위해  고속절단
기를 사용하지 마십시오.

올바른 복장차림

 헐렁한 옷이나 장신구를

착용하지 마십시오. 움직이는 부분에 걸릴 수
있습니다. 실외에서 작업할 때에는 미끄럼
방지 신발을 착용하는 것이 좋습니다. 
긴머리일 경우 잘 감싸서 보호하십시오.

보호 장비를 사용하십시오.

보호 안경을 착용하십시오. 절단 작업으로
먼지가 발생할 경우 방진 마스크를 사용하
십시오.

1.

2.

3.

4.

5.

6.

7.

8.

9.

Содержание MS10W2





































Отзывы: