REXON MS10W2 Скачать руководство пользователя страница 5

5

of dust extraction and collecting 

equipment, ensure these are connected 

and properly used.

11. 

Do not abuse the cable.

 Never pull the 

cable to disconnect it from the socket. 

Keep the cord away from heat, oil and 

sharp edge.

12. 

Secure work.

 Where possible use 

clamps or a vise to hold the work. It’s 

safer than using your hand.

13. 

Don’t overreach.

 Keep proper footing 

and balance at all time.

14. 

Maintain tools with care.

 Keep 

cutting tools sharp and clean for 

better and safer performance. Follow 

instructions for lubricating and 

changing accessories. Inspect tool 

cords periodically and if damaged 

have them repaired by an authorized 

service facility. Inspect extension cords 

periodically and replace if damaged. 

Keep handles dry, clean and free from 

oil and grease.

15. 

Disconnect tools.

 When not in use, 

before servicing and when changing 

accessories such as blades, bits, cutters, 

disconnect tools from the power supply.

16. 

Remove adjusting keys and 

wrenches.

 Form the habit of checking 

to see that keys and adjusting wrenches 

are removed from the tool before turning 

it on.

17. 

Avoid unintentional starting.

 Ensure 

switch is in “off” position when plugging in.

18. 

Use outdoor extension leads.

 When 

the tool is used outdoors, use only 

extension leads intended for outdoor 

use and so marked.

19. 

Stay alert.

 Watch what you are doing, 

use common sense and do not operate 

the tool when you are tired.

20. 

Check damaged parts.

 Before further 

use of the tool, it should be carefully 

checked to determine that it will operate 

properly and perform its intended 

function. Check the alignment of moving 

parts, binding of moving parts, breakage 

of parts, mounting and any other 

conditions that may affect its operation. 

10. 

Connect dust extraction equipment.

 If 

devices are provided for the connection 

먼지 집진 장비를 연결하십시오.

 분진 추출 및

집진 장비를 연결할 경우 정확히 연결되고 작 
동하는지 확인하십시오.

전기 코드선을 남용하지 마십시오.

 전기 코드

선을 잡아 당기면서 콘센트에서 분리하지
마십시오. 전기 코드선을 열, 기름 및 칼날에 
가까이하지 마십시오.

안전한 작업

 가능하면 클램프나 바이스를 

사용하여 작업하십시오. 자재를 손으로 잡고 
작업하는 것은 위험합니다.

적정 거리를 유지하십시오.

 항상 적절한 평형

과 균형을 유지하십시오.

고속절단기를 관리하십시오.

 더 좋고 더 안전

한 성능을 위해 절삭 공구를 예리하고 깨끗하
게 유지하십시오. 윤활제 및 액세서리 교체 지
침을 따르십시오. 정기적으로 전기코드선을 
점검하고 손상된 경우 공인 서비스 기관에서 
수리해야 합니다. 연장 코드선을 주기적으로 
점검하고 손상된 경우 교체하십시오. 핸들은 
건조하고 깨끗하게 유지하고 오일과 구리스가 
없어야 합니다.

전원을 끄십시오.

 기계를 사용하지 않을 때, 

이동하기 전이나 톱날, 비트, 커터와 같은 
액세서리를 교체 할 때 전원 공급 장치에서  
코드선을 분리하십시오.

조절 키와 렌치를 제거하십시오.

 고속절단기를 

사용하기전에 키와 조절 렌치가 기계에서 
제거되었는지 확인하는 습관을 가지십시오.

계획하지 않은 작동을  피하십시오.

 전원연결시 

스위치가 "꺼짐"위치에 있는지 확인하십시오.

실외용 전선릴을 사용하십시오.

 기계를 실외에

서 사용할 때에는 옥외용으로 검증된 전선릴만 
사용하십시오.

항상 주의하십시오.

 자신의 상태를 확인하고, 

피곤할 때에는 기계를 작동하지 마십시오.

손상된 부품을 확인하십시오.

 기계를 사용하기 

전에 기계가 올바르게 작동하고 제대로 된 기
능을 수행하는지 주의 깊게 점검해야 합니다. 
움직이는 부품의 정렬, 움직이는 부품의 조임, 
부품의 파손, 장착 및 작동에 영향을 미칠 수
있는 기타 조건을 점검하십시오.

10.

11.

12.

    
13.

14.

15.

16.

17.

18.

19.

20.

 보호장치 또는 기타 손상된 부품은 본 사용 

설명서에 별도의 표시가 없는 한 공인된 서비
스 센터에서 수리하거나 정품으로 교체해야 
합니다. 스위치로 전원을 켜고 끌 수 없는 경우 
기계를 사용하지 마십시오.

Содержание MS10W2





































Отзывы: