background image

3

BEFORE EACH USE

1.

  INSPECT YOUR THICKNESSER:

●  If any part is missing, bent or broken 

in any way, or any electrical part does 

not work properly, turn the thicknesser 

OFF and unplug the thicknesser.

●  Replace damaged or missing parts 

before using the thicknesser.

●  Make sure the cutterhead turns in 

the right direction. They should move 
toward the infeed table.

2. 

AVOID INJURY FROM JAMS, SLIPS 

OR THROWN PLECES (KICKBACKS):

●  Use this thicknesser only for wood or 

similar materials.

●  Plan your hand placement so your 

fingers will not be in a place where a 

sudden slip could cause them to slide 

or fall into the cutterhead. When using 

only one push block to feed the wood, 

do not put your other hand on the 

thicknesser or workpiece.

●  Avoid injury from thrown pieces. Make 

sure the blades are properly installed 

and the cutter blade wedge screws 

  are tight.

●  Adjust the depth of cut to between 

  0.8 mm or less for best results. A deep 

cut makes feeding the wood harder 

and can cause the wood to kickback.

●  Use the right tool. Do not force the tool 

to do a job it is not intended to do.

3. 

INSPECT YOUR WORK AREA:

●  Keep the work area clean.

●  Cluttered area and benches invite 

accidents. The floor must not be 

slippery from wax or sawdust.

●  Avoid burns or other fire damage. 

Do not use the thicknesser near 

flammable liquids, vapours or gases.

●  Before using the thicknesser, clear the 

table of all objects not needed to feed 

the workpiece.

●  Avoid injury. Do not perform layout, 

assembly, or setup work on the 

thicknesser.

4.

  PLAN YOUR WORK:

●  Before trying a new or not often used 

operation, carefully plan your hand 

placement. Make sure you have proper 

push blocks, jigs, fixtures, stops, and 

other items ready to use.

●  Avoid injury form unsafe accessories. 

Use only recommended accessories.

5.  

DRESS FOR SAFETY:

●  Plan ahead to protect your eyes, 

hands, face and  ears.

●  Do not wear loose clothing, gloves, 

neckties or jewellery (rings, wrist 

watches). They can get caught and 

draw you into moving parts.

●  Wear nonslip footwear.

●  Tie back long hair.

●  Roll long sleeves above the elbow.

●  Noise levels vary widely. To avoid 

possible hearing damage, wear 

ear plugs or muffs when using the 

thicknesser for hours at a time.

●  Thicknesser can throw foreign objects 

into your eyes. This can result in 

permanent eye damage. Wear safety 

goggles (not glasses). Regular 

eyeglasses have only impact-resistant 

lenses. They are not safety glasses.

●  For dusty operations, wear a dust 

mask along with safety goggles.

6. 

INSPECT YOUR WORKPIECE:

●  Make sure there are no nails or foreign 

objects in the part of the workpiece to 

be planed.

7. 

PLAN YOUR CUT:

●  Small or thin workpieces can kickback 

when they tip over on the tables or the 

cutterhead.

●  To avoid cutterhead contact or 

workpiece kickback, do not plane 

workpieces shorter than 127 mm.

●  Do not plane wood thinner than 13 mm.

●  Do not cut freehand. Guide your 

workpiece solidly against the fence 

and table top. Make sure there in no 

debris between the workpiece and its 

supports.

●  Use extra caution with large, small or 

awkward workpieces.

Содержание AP3300





















Отзывы: