Rexnord Falk A Скачать руководство пользователя страница 26

Страница: 26 / 44

Rexnord Industries, LLC 3001 W. Canal St., Milwaukee, WI 53208-4200 USA

378-200

(PN-2128394)

Telephone: 414-342-3131 Fax: 414-937-4359

November 2010

e-mail: [email protected] web: www.rexnord.com

Supersedes 6-07

TABLE 4 — Synthetic Lubricants – Polyalphaolefin Type

‡

Ambient Temp. Range

–30 to +10°F

(–34 to –12°C)

–15 to +50°F

(–26 to +10°C)

0 to +80°F

(–18 to +27°C)

+10 to +125°F

(–12 to +52°C)

+20 to +125°F

(–7 to +52°C)

AGMA Viscosity Grade

ISO Viscosity Grade

150

220

320

Viscosity cSt @ 40°C

28.8-35.2

61.2-74.8

135-165

198-242

288-352

Viscosity SSU @ 100°F

134-164

284-347

626-765

918-1122

1335-1632

Manufacturer

Lubricant

Chevron U.S.A., Inc.

. . .

Clarity Synthetic PM Oil 220

. . .

Syn. Gear Lube Tegra 220

Conoco Inc.

Syncon R & O 32

Syncon R & O 68

Syncon EP 150

Syncon R & O 220

Syncon EP 320

Syncon EP 68

Syncon EP 220

Dryden Oil Co.

Dryden SHL Lubricant 32

Dryden SHL Lubricant 68

Dryden SHL Lubricant 150

Dryden SHL Lubricant 220

Dryden SHL Lubricant 320

Exxon Company, U.S.A.

Teresstic SHP 32

Teresstic SHP 68

Teresstic SHP 150

Teresstic SHP 220

Teresstic SHP 320

Spartan Synthetic EP 150

Spartan Synthetic EP 220

Spartan Synthetic EP 320

Mobil Oil Corp.

SHC 624

SHC 626

SHC 629

SHC 630

SHC 632

Mobilgear SHC 150

Mobilgear SHC 220

Mobilgear SHC 320

Pennzoil Products Co.

Pennzgear SHD 32

Pennzgear SHD 68

Pennzgear SHD 150

Pennzgear SHD 220

Pennzgear SHD 320

Super Maxol “S” 68

Super Maxol “S” 150

Super Maxol “S” 220

Super Maxol “S” 320

Petro-Canada Products

. . .

Super Gear Fluid 150EP

Super Gear Fluid 220EP

Super Gear Fluid 320EP

Shell Oil Co.

. . .

Hyperia 220

Hyperia 320

Hyperia S 220

Hyperia S 320

Sun Co.

. . .

Sunoco Challenge 220

Sunoco Challenge 320

Sunoco challenge eP 220

Sunoco Challenge EP 320

Texaco Lubricants Co.

Pinnacle 32

Pinnacle 68

Pinnacle 150

Pinnacle 220

Pinnacle 320

Pinnacle EP 150

Pinnacle EP 220

Whitmore Manufacturing Co.

. . .

Decathlon 4EP

Decathlon 5EP

Decathlon 6EP

‡

Minimum viscosity index of 130. Consult lubricant supplier/manufacturer for maximum operating temperature.

Minimum viscosity index of 120.

Extreme pressure EP lubricant (contains sulphur-phosphorus).

DO NOT

use in drive equipped with internal backstop.

Drives

NOT

equipped with internal backstop may widen the ambient temperature range to -25 to +125°F (-32 to 5 2°C).

Appendix A

•

Falk™ Quadrive Shaft Mounted Drives Model A

(Page 26 of 44)

Sizes 5107-5315

Содержание Falk A













































Результаты поиска

Содержание Falk A

Отзывы:

Похожие инструкции для Falk A

Бренды по названию

Популярные бренды

Rexnord Falk A, Руководство пользователя

Результаты поиска

Содержание Falk A

Отзывы:

Похожие инструкции для Falk A

Бренды по названию

Популярные бренды