manualshive.com logo in svg

Rexel 1150 S2, Иллюстрированный перечень запчастей и инструкции по обслуживанию

Поделиться
Скачать
Rexel 1150 S2 Скачать руководство пользователя страница 43

Deskside and Office 230v

42

26/05/99

ILLUSTRATED PARTS MANUALS
SERIES 7 SHREDDERS – 230v
DESKSIDE AND OFFICE MODELS

Replacement of damaged strippers

:-

1. Slide out stripper support bars to the extent
    necessary.
2. Lift out damage strippers.
3. Fit new plates, (two per groove S3 models, one per
    groove S4 model).
4. Replace support bars

In the event that strippers and cutting shafts become partially or fully disengaged:-

1.

Separate completely the cutter shaft from its stripper plates.

2.

Pull out the two support bars.

3.

Arrange the cutting shaft such that the motor end is to your left, and therefore the nearer shaft
to you is the one towards the front of the machine.

4.

Place one pair of stripper plates (model S3) in the first groove of its cutter (one per groove –
S4 model) such that support bar holes are to the front (for nearer cutter) or the back (for rear
cutter), and the semi-circular cut out of the stripper faces downwards over the cutter inner
diameter.

5.

In the same way, fit strippers to all grooves and repeat for the other cutter if necessary.

6.

Slide in the stripper support bars.

Replacement of cutter shaft assembly into frames

1.

Carefully engage the two cutters, blades of one in the grooves of the other, with shaft ends
aligned for correct assembly to side frames.

Содержание 1150 S2



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды