Revox Re:system M10 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 40

Revox Re:system M10 Скачать руководство пользователя страница 9

M10

Re:system

7

Installation and assembly

The M10 is an 19“ build-in unit, which
was principally conceived for
insertion into a 19” cabinet. Thanks to
the integrated unit feet, however, it is
possible to position it outside of a 19”
cabinet.

Installation in a 19“ cabinet
The M10 has variable side-elements
that enable installation in the 19”
cabinet. These can be assembled in 2
different positions on the M10 and
enable the installer to assemble it in
the 19” cabinet in the best possible
way. See the figure below.

The M10 can be installed with the
plug-in slots directed to the front or
the back. See figure on Page 9.
Depending on the cabling strategy,
the plug-in module cables can be fed
in at the front of the unit or concealed
at the back.

In both positions, it is possible to
position the M10 4 cm towards the
inside. This is a particular benefit in
the case of 19” cabinets with a door
as this allows you to plug the cable in
at the front without it being unduly
kinked.

Seitenansicht:

M10 mit vorge-

setztem Halte-

winkel

Side view:

M10 with flush
retaining bracket

Side view:

M10 with forward-
spaced retaining
bracket

«
...
7
8
9
10
11
...
»

Содержание Re:system M10









































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды