rEvo Rebreathers rEvo III micro FT Скачать руководство пользователя

Страница: 30 / 33

Manual rEvo III

Appendix A: Drills:

The following scenarios must be practiced during any rEvo training. Your instructor
will teach how to react to.

•

High PPO2.

•

Low PPO2.

•

PPO2 low / empty oxygen cylinder.

•

PPO2 high / empty diluent cylinder.

•

Hissing noise, no change of PPO2.

•

Empty diluent cylinder / empty wing.

•

Water in the breathing hose.

•

Water in the inhale lung.

•

Stuck open manual oxygen addition valve.

•

Stuck closed manual oxygen addition valve.

•

Stuck open manual diluent addition valve.

•

Stuck closed manual diluent addition valve.

•

ADV stuck open.

•

ADV not working.

•

Inflator stuck open.

•

Broken wing.

•

Cells give different readings.

•

1 cell completely dead.

•

2 cells completely dead.

•

Head aches, dizziness, feelings of uncertainty.

Содержание rEvo III micro FT


































Результаты поиска

Содержание rEvo III micro FT

Отзывы:

Похожие инструкции для rEvo III micro FT

Бренды по названию

Популярные бренды

rEvo Rebreathers rEvo III micro FT, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание rEvo III micro FT

Отзывы:

Похожие инструкции для rEvo III micro FT

Бренды по названию

Популярные бренды