Retsch ABP 250 Скачать руководство пользователя страница 44

Страница: 44 / 57

Cleaning, Wear and Maintenance

7.1.1 Removing and installing the feed hopper

WARNING

W8.0003

Serious personal injury

Contact between moving jaws in the grinding chamber



Accidentally reaching into the grinding chamber and between moving jaws

can cause serious injuries to hands.

•

Always operate the device with the feed hopper installed.

Fig. 28:

Removing and assembling the feed hopper

Removing the feed hopper



Switch the ABP 250 off.



Disconnect the ABP 250 from the power supply and secure to prevent it restarting.



Unscrew the M6 Allen screw (



Lift the feed hopper (

) up and out.

Assembling the feed hopper



Slide the feed hopper (

) downwards from above over the guide plate (



Secure the feed hopper (

) using the M6 Allen screw (

7.1.2 Cleaning the feed hopper

WARNING

W9.0003

Serious personal injury

Contact between moving jaws in the grinding chamber



Accidentally reaching into the grinding chamber and between moving jaws

can cause serious injuries to hands.

•

Always operate the device with the feed hopper installed.

Содержание ABP 250


























































Результаты поиска

Содержание ABP 250

Отзывы:

Похожие инструкции для ABP 250

Бренды по названию

Популярные бренды

Retsch ABP 250, Руководство пользователя

Результаты поиска

Содержание ABP 250

Отзывы:

Похожие инструкции для ABP 250

Бренды по названию

Популярные бренды