background image

SV9401/SV9402/SV9403, SV9501/SV9502/SV9503, SV9601/SV9602 SMARTVALVE™

69-1004—01

2

Table 2. Capacity and Inlet and Outlet Specifications.

a

 Capacity based on 1000 Btu/ft

3

, 0.64 specific gravity at 1 in. wc pressure drop (37.3 MJ/m

3

,0.64 specific gravity

natural gas at 0.25 kPa pressure drop).

b

 Minimum regulation for LP gas is 15,000 Btuh.

c

 Minimum regulation for LP gas is 40,000 Btuh.

d

 Capacity is reduced by 5 percent with the use of optional outlet screen.

e

 Valves are guaranteed only at 77 percent of the rating.

Table 3. Model Number Suffix Letter Description.

Electrical Ratings:

System Transformer: 40 VA minimum NEMA-rated trans-

former. Control systems using SV9601, SV9602, or 

other large secondary loads may require a larger 

transformer. Refer to the appliance manufacturer rec-

ommendation.

Voltage and Frequency: 24 Vac, 50/60 Hz.

Current draw at 24 Vac: 24V Hot: 1.25A nominal (1.5A 

maximum) when igniter is powered.

24V Thermostat: See Table 4.

Electronic Fan Timer Output: 0.1A maximum at 24 Vac.

Output is 8 Vac less than thermostat input voltage at 

0.1A draw.

Table 4. Thermostat Current (Run Mode).

Ignition Sequence Timing at 60 Hz 
Input

Prepurge Time (Factory-set on SV9402, SV9502, and 

SV9602):

15 or 30 seconds depending on model.

Trial for Ignition:

90 seconds.

Automatic Reset Time:

5 minutes.

NOTE:

The SV9403 and SV9503 are lockout models 

and do not provide Automatic Reset Time.

Flame Failure Response Time:

1.6 seconds maximum at 3 mA.

IMPORTANT

All timings increase by 20 percent with 50 Hz 

input.

Gas Conversion Kits:

See Table 5 for gas conversion kit information.

NOTE:

See appliance manufacturer specifications and 

instructions and information in these installa-

tion instructions before attempting to convert 

an appliance.

Pipe Adapters:

Angle and straight flange adapters available for 3/8-, 

1/2- and 3/4-in. NPT pipe. See Table 6.

NOTE:

Models with 3/4 in. inlet or outlet do not accom-

modate the adapter kits.

Model

Size

Inlet x Outlet (in.)

Capacity (at 1 in. wc 

pressure drop

a

)

Minimum Regulated 

Capacity

Maximum Regulated 

Capacity

SV9401/SV9402/

SV9403

1/2 x 1/2 NPT

85 ft

3

/hr

(2.3m

3

/hr)

10 ft

3

/hr (0.4m

3

/hr)

b

120 ft

3

/hr

(3.4m

3

/hr)

SV9501/SV9502/

SV9503

1/2 x 1/2 NPT

150 ft

3

/hr

(4.2m

3

/hr)

20 ft

3

/hr (0.6m

3

/hr)

c

200 ft

3

/hr

(5.7m

3

/hr)

SV9501

1/2 NPT x 1/2 

inverted flare

130 ft

3

/hr

(3.7m

3

/hr)

20 ft

3

/hr (0.6m

3

/hr)

c

180 ft

3

/hr

(5.1m

3

/hr)

SV9601/SV9602

d

1/2 x 1/2 NPT

240 ft

3

/hr

(6.8m

3

/hr)

e

20 ft

3

/hr (0.6m

3

/hr)

c

340 ft

3

/hr

(9.6m

3

/hr)

e

1/2 x 3/4 NPT

270 ft

3

/hr

(7.6m

3

/hr)

e

30 ft

3

/hr (0.8m

3

/hr)

370 ft

3

/hr

(10.5m

3

/hr)

e

3/4 x 3/4 NPT

300 ft

3

/hr

(8.5m

3

/hr)

e

30 ft

3

/hr (0.8m

3

/hr)

415 ft

3

/hr

(11.8m

3

/hr)

e

Model No. Suffix Letter

Ambient Temperature Range

Pressure Regulator Type

H

0°F to 175°F (-18°C to +79°C)

Slow opening

M

-40°F to +175°F (-40°C to +79°C)

Standard opening

P

-40°F to +175oF (-40°C to +79°C)

Step opening

R

-40°F to +175°F (-40°C to +79°C)

Standard opening–convertible (Natural/LP) for 

mobile home application.

Model

24 Vac, 50/60 Hz

SV9401/SV9402/SV9403

0.20A/0.20A

SV9501/SV9502/SV9503

0.20A/0.20A

SV9601/SV9602

0.20A/0.20A

Содержание SmartValve SV9401

















Отзывы: