manualshive.com logo in svg

Republic Manufacturing RB-SERIES, Инструкция по установке и эксплуатации

Поделиться
Скачать
Republic Manufacturing RB-SERIES Скачать руководство пользователя страница 36

www.republic-mfg.com

800.847.0380

36

Using a 1 inch (25.4 mm) open-end wrench, as shown in Figures 3 and 4, rotate the Tension Arm Assembly clockwise (CW) and 

remove the Belt. You may release the pressure on the wrench and allow the Tension Arm to swing back into position once the Belt 
has been removed.

Using a 1 inch (25.4 mm) open-end wrench, rotate the Tension Arm Assembly clockwise (CW). Wrap the new or replacement Belt 
around the Blower Pulley and then onto the Motor Pulley as shown in Figures 5 and 6. Once the Belt is in place and the wrench is 
removed, verify that the Belt is seated into all the grooves on both pulleys by manually rotating the Motor Pulley (large pulley), and 
checking the alignment of the Belt on the groves. 

 

Note:

  The same belt removal and installation procedure applies for the RB2400 Model with one exception–there are two (2) belts.

Figure 3

1” Open End 

Wrench

Tension Block 

rotated away

Figure 4

Tension Pulley rotated 

away from belt

Tension Pulley

Belt

Blower Pulley

Motor Pulley

Figure 5

Figure 6

Содержание RB-SERIES







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды