manualshive.com logo in svg

Republic Manufacturing RB-SERIES, Инструкция по установке и эксплуатации

Поделиться
Скачать
Republic Manufacturing RB-SERIES Скачать руководство пользователя страница 20

www.republic-mfg.com

800.847.0380

20

Motor Wiring and Start-Up

  Only qualified mechanical or electrical personnel should perform wiring or maintenance on the blower assembly.

 

Never run a centrifugal blower to atmosphere, as this can cause overloading and damage the motor. Always  

  check your installation to make sure the motor is running within the motor manufacturers specific amp ranges.

 

Republic blowers are shipped with the belts removed. Motor rotation must be checked prior to installing the  

   belt! Running the blower/motor assembly backwards will cause improper performance and damage the blower.

 

With the belt removed, “bump” the power to determine rotation of motor.

 

The blower should be rotating clockwise (CW) from the belt side of the blower, counter-clockwise (CCW)  

    if you are on the motor side or impeller side of the blower. Rotation arrows on the blower cast housing  

    (Motor Side) show correct rotation of impeller rotation. If the motor is going the wrong direction, then have  

    your qualified electrician change the direction of rotation.

 

If the blower is allowed to run in the wrong direction, you could cause damage to the idler pulley assembly  

    spring or belt. Even in reverse, a centrifugal blower will still provide a substantial amount of airflow and  

    pressure, but it will not perform to your satisfaction.

Содержание RB-SERIES







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды