background image

Installation Guide                                                      RN3000US Apr 2013 

48 

3.  If the system problem persists, contact RENOVO POWER technical support 

at: 855-RENOVO1 (736-6861) 

In order to better assist you when contacting RENOVO POWER, please provide 
the following information:   

 

Required Information for Digiwatts Unit Service: 

 Serial 

number 

 Model 

number 

  Short description of the problem 

 Display 

message 

  What error code is indicated? 

  AC line voltage 

  DC line voltage 

  Can you reproduce the failure?    If yes, how? 

  Has this problem occurred in the past? 

  What were the ambient conditions when the problem occurred? 

 

Information Regarding the PV Modules: 

  Manufacturer name and model number of the PV module 

  Output power of the module 

  Open circuit voltage (Voc) of the module 

  Number of modules in each string 

If it becomes necessary to send the Digiwatts unit back to the manufacturer for 
service, please ship it in the original packaging to avoid damage during shipping. 

8.2 Error Messages 

If a fault occurs, the Digiwatts system generates an error message according to 
the operating mode and the detected fault. 

 

 

Содержание Digiwatts RN3000US























































Отзывы: