Renovo Digiwatts RN3000US Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 54

background image

Installation Guide RN3000US Apr 2013

29

security.)

Figure 4-9 Affix Bottom Tabs of Digiwatts unit to Mounting Bracket

3) Inspect the Digiwatts unit from both sides to ensure that it sits centered on

the wall screws.

4) Carefully verify that the Digiwatts unit is mounted firmly in place.

5 Wiring the Digiwatts unit

This section provides step-by-step procedures and other information required
for wiring the Digiwatts unit to the PV array and the utility grid. To complete the
installation in a safe and efficient manner, complete the steps in the order that
they appear.

WARNING!

Before connecting or operating the Digiwatts unit, read all of the
instructions, cautions, and warnings on the Digiwatts unit, the PV array
and in this Installation Guide.

WARNING!

You must connect the wires that carry the AC voltage from the Digiwatts
unit to the utility grid and the wires that carry the DC voltage from the PV
array to the Digiwatts unit in the order described in the procedures in this
section. Deviating from these procedures could expose you to lethal
voltage.

M6 machine screw

Lock

«
...
28
29
30
31
32
...
»

Содержание Digiwatts RN3000US























































Отзывы:

Нет отзывов

Похожие инструкции для Digiwatts RN3000US

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 30

Бренд: Yamaha Страницы: 30

EF4500iSE - Inverter Generator

Бренд: Yamaha Страницы: 10

blueplanet 3.0 TL3 M2 WM OD IIG0

Бренд: Kaco Страницы: 262

Бренд: Schumacher Страницы: 45

Бренд: Tripp Lite Страницы: 4

Бренд: Magnimage Страницы: 40

Бренд: Gbxpoint Страницы: 4

Бренд: M-system Страницы: 5

Бренд: Nuova Marea Страницы: 9

Бренд: Tyba Страницы: 14

ELinx EIR-G-SFP-T

Бренд: B&B Electronics Страницы: 2

Бренд: Nagra Страницы: 18

Бренд: IVIEW Страницы: 40

Бренд: Mitsubishi Страницы: 2

Бренд: Hall Research Technologies Страницы: 8

Бренд: Yuan Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды