Renovo Digiwatts RN3000US Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 54

background image

Installation Guide RN3000US Apr 2013

35

5.4 Wiring the DC input

This subsection provides procedures for wiring the DC input from the PV array
to the Digiwatts unit.

5.4.1 DC Connection Requirements

WARNING!

All electrical installations must be done in accordance with all local
electrical codes and with the National Electrical Code (NEC),
ANSI/NFPA 70. For installation in Canada the installations must be
done in accordance with applicable Canadian standards.

WARNING!

Use #8 AWG-10AWG, 105 °C, copper wire for all DC wiring connections
to the Digiwatts. Voltage drop and other considerations may dictate
that larger size wires be used. Use only solid or stranded wire but not
fine stranded wire.

WARNING!

Any additional DC disconnect for the inverter must have a minimum
rating of 600VDC and 25A continuous.

Information

Series fusing may be required depending on the type of PV module used
in the system. See NEC 690.9.

WARNING!

You must connect the wires that carry the DC voltage from the PV array to the
Digiwatts unit in the order described in the following procedure. Deviating from
this procedure could expose you to lethal voltages that can cause serious injury
and/or death.

«
...
34
35
36
37
38
...
»

Содержание Digiwatts RN3000US























































Отзывы:

Нет отзывов

Похожие инструкции для Digiwatts RN3000US

Бренд: Patton electronics Страницы: 16

Бренд: Danfoss Страницы: 36

Бренд: L-Card Страницы: 73

Бренд: WATANABE Страницы: 2

Бренд: M-Audio Страницы: 24

Бренд: DeLOCK Страницы: 16

Бренд: Velleman Страницы: 11

Бренд: Duracraft Страницы: 62

Бренд: Duracell Страницы: 37

PWRIG100012120S

Бренд: AIMS Power Страницы: 16

Бренд: YUAN High-Tech Страницы: 12

Бренд: Panasat Страницы: 33

Бренд: Parkside Страницы: 41

IGSI - 3 Series

Бренд: InfluxGreen Страницы: 37

Бренд: Sabaj Страницы: 18

Бренд: IMC Networks Страницы: 8

Бренд: Seko Страницы: 13

Бренд: Nagra Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды