•
The mains socket into which the power adapter is plugged must be easily accessible.
• Do not pull the AC adapter from the power outlet by pulling on the cable.
• If the wall plug transformer is damaged, do not use the product any longer.
Switch off the mains socket to which the wall plug transformer is connected (switch
off at the corresponding circuit breaker or remove the safety fuse, then switch off
the earth leakage circuit breaker). Unplug the wall plug transformer from the mains
socket.
Replace the defective wall plug transformer only with a wall plug transformer of
the same design (with the same output voltage, output current, round plug and plug
polarity).
• If it can be assumed that safe operation is no longer possible, the device must be
turned off and precautions must be taken to ensure that it is not used unintentionally.
Safe operation can no longer be assumed if:
- the product shows visible signs of damage
- the product does not work at all or works poorly (where there is flickering light,
leaking smoke or a smell of burning, audible crackling noises, or discolouration of
the product or to adjacent surfaces)
-
the product was stored for a longer period of time in unfavourable conditions
- it was exposed to heavy loads during transport
• For safety reasons, unplug the wall plug transformer from the mains socket before
cleaning the product or when the product is not to be used for a while (e.g., during
storage).
Instructions concerning the battery
• Batteries should be kept out of the reach of children.
• Do not leave batteries lying around in the open; there is a risk of them being swallowed by
children or pets. If they are swallowed, consult a doctor immediately.
• Leaking or damaged batteries can lead to caustic burning of the skin. Therefore, use suitable
protective gloves.
• Liquids leaking from batteries are very chemically aggressive. Objects or surfaces coming into
contact with these liquids might be considerably damaged. Therefore, store batteries in a suit
-
able location.
• Batteries must not be short-circuited, opened or thrown into a fire. There is a risk of explosion!
• Do not recharge normal, non-rechargeable batteries; there is a risk of explosion!
• Please pay attention to the correct polarity (plus/+ and minus/-) when inserting the battery.
Mounting and start-up
a) Mounting the control unit
Before you start the installation, keep in mind that the IR receiver of the control unit
must be placed so that a flawless reception of the control signals from the IR remote
control is possible.
A direct optical contact between the IR LED of the IR remote control and the IR receiver
is beneficial, however it is not a prerequisite. The IR light (invisible to the human eye) of
the IR remote control is reflected by many surfaces.
Before you proceed to the permanent mounting of the control unit and the IR receiver,
check that they function properly.
• The control unit can be screwed tight via two eyes located on the sides of the housing. Depend
-
ing on the mounting site, you can also fasten the control unit using cable ties or a double-sided
adhesive tape.
When you screw the control unit into place, make sure that no cable or pipes are dam
-
aged when drilling and tightening the screws.
• Fasten the IR receiver of the control unit to a suitable place, e.g. by using a strip of adhesive tape
or a cable tie.
b) Installing the LED strip
• The LED strip can be mounted on suitable surfaces, such as furniture or similar objects, using
the adhesive tape located on the underside.
The LED strip must be mounted in such a way that it is not exposed to mechanical
stress. It may not be mounted in such a way that someone can step on it; that will dam
-
age it.
• Carefully clean the surface onto which you want to mount the LED strip from dust, dirt and
grease before mounting; otherwise the adhesive tape will come off the surface.
• Remove part of the protective strip and stick the LED strip onto the mounting surface one section
at a time. However, do not use force when pressing down.
The LED strip can be cut at the marked points. The connectors provided can be used
to restore the electrical connection between the individual LED strip sections.
c) Connecting the LED strip to the control unit
• The diagram below demonstrates how to connect the LED strip to the control unit.
Dout
R3
C2 R4
• The plug connection can be protected from unintentional disconnection by using a strip of ad
-
hesive tape.
d) Connecting the wall plug transformer
• Connect the round low voltage plug of the wall plug transformer to the corresponding round
socket on the control unit.
• Connect the wall plug transformer to a proper mains socket of the public supply network.
Operating Instructions
LED strip, digital colour change, 5 m
Item no. 1193533
Intended use
The product is intended for decorative or effect lighting in indoor areas; it may be installed and
used only in dry, enclosed indoor rooms.
The product can be fastened on suitable objects, such as furniture, using the adhesive tape lo
-
cated on the bottom side of the LED strip.
The light programme and lighting colours can be selected and controlled via the IR remote control
enclosed. The activation of the LEDs on the LED strip takes place via a special control unit, the
power for which is supplied by the provided mains adapter.
Always observe the safety instructions and all other information included in these operating in
-
structions.
Any use other than that described above could lead to damage to this product and involves the risk
of short circuits, fire, electric shock, etc.
This product complies with the applicable national and European requirements. All names of com
-
panies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• LED Strip
• Control unit with integrated IR receiver
• IR remote control (incl. batteries)
• AC adapter
• Accessory set (2x screws for mounting the control unit, 4 connection cables, 3M tape)
• Operating instructions
Explanation of symbols
The lightning symbol inside a triangle is a warning to inform you of potential risks of
personal injury, such as electric shock.
This symbol indicates specific risks associated with handling, function or operation.
The “arrow” symbol indicates special tips and operating information.
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe these
safety instructions! We do not assume any liability for any resulting damage!
We shall not accept liability for damage to property or personal injury caused by in-
correct handling or non-compliance with the safety instructions. In such cases, the
warranty will be null and void.
a) General
• Unauthorised conversion and/or modification of the product is not allowed for safety
and approval reasons.
• The product is not a toy and does not belong in the hands of children! Children do
not realise the danger arising from the incorrect use of electrical devices. In addi
-
tion, the product contains small parts and batteries. Therefore, be especially careful
when children are around!
• Do not leave packaging material carelessly lying around, since it could become a
dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the Employer’s Li
-
ability Insurance Association for Electrical Systems and Operating Facilities are to
be observed!
• If you have any questions that are not answered in this manual, please contact our
technical service or other specialist.
b) Installation, connection and operation
• This product must be installed and used only in dry conditions indoors. The product
must not get damp or wet, as the wall plug transformer can pose the risk of a fatal
electric shock!
• Do not use the product in rooms that are under adverse environmental conditions,
where combustible gases, vapours or dust are or may be present! There is a risk of
explosion!
• The product must not be exposed to extreme temperatures, strong vibrations or
heavy mechanical stress.
• The product is suitable for use only in moderate climates, not tropical climates.
• Caution, LED light: Do not look directly into the LED light! Do not look into the beam
directly or with optical instruments!
