Renesas H8S/2378F Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 170

background image

12

Note:

When installing the PCI card emulator, note the following:
1. Turn off the host computer.
2. Insert the emulator into the PCI slot in parallel.
3. Screw in the emulator after confirming the connector and cable positions.

2.4

Connecting the Card Emulator with the User System

(1) The connector must be installed to the user system. Table 2.1 shows the recommended

connector for the emulator.

Table 2.1 Recommended Connector

Type Number

Manufacturer

Specifications

2514-6002

3M Limited

14-pin straight type

Note: When the connector is used, do not install any components within 3 mm of the

connector.

(2) The pin arrangement of the connector is shown in section 6.2, Pin Arrangement of the Hitachi-

UDI Port Connector.

(3) Figure 2.4 shows how to connect the user system interface cable to the user system. Connect

the ground line of the cable to the user system ground. The end of the ground line has a hole
having a diameter of 3 mm, and therefore, when the ground line is screwed to the user system,
the screw diameter must be 3 mm.

Figure 2.4 Connecting the User System Interface Cable to the User System

«
...
34
35
36
37
38
...
»

Содержание H8S/2378F











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8S/2378F

Бренд: 3M Страницы: 3

E-20 - Dual Monaural Earphones

Бренд: Olympus Страницы: 2

Бренд: Novation Страницы: 93

Бренд: ICP Страницы: 60

Saving and Recovering Your Factory and System Images

Бренд: Fujitsu Страницы: 16

Бренд: Fujitsu Страницы: 52

Restoring Microsoft Windows® 7 Edition

Бренд: Fujitsu Страницы: 4

ServerView Event Manager

Бренд: Fujitsu Страницы: 172

Бренд: Fujitsu Страницы: 45

Бренд: Fujitsu Страницы: 234

ServerView Operations Manager V6.12

Бренд: Fujitsu Страницы: 282

ServerView Virtual-IO Manager V3.1

Бренд: Fujitsu Страницы: 362

ServerView Resource Orchestrator Cloud Edition V3.1.1 Operation

Бренд: Fujitsu Страницы: 414

Remote Management

Бренд: Fujitsu Страницы: 426

Configuring Arrays

Бренд: HP Страницы: 132

Бренд: HP Страницы: 26

Бренд: HP Страницы: 35

460C - Deskjet Color Inkjet Printer

Бренд: HP Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды