Renesas H8S/2378F Скачать руководство пользователя страница 10

Страница: 10 / 170

SAFETY PAGE

READ FIRST

• READ this user's manual before using this emulator product.

• KEEP the user's manual handy for future reference.

Do not attempt to use the emulator product until you fully understand its mechanism.

DEFINITION OF SIGNAL WORDS

This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.

DANGER

DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.

WARNING

WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.

CAUTION

CAUTION used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may result
in property damage.

NOTE

emphasizes essential information.

Содержание H8S/2378F











































































































































































Результаты поиска

Содержание H8S/2378F

Отзывы:

Похожие инструкции для H8S/2378F

Бренды по названию

Популярные бренды

Renesas H8S/2378F, Руководство пользователя

Результаты поиска

Содержание H8S/2378F

Отзывы:

Похожие инструкции для H8S/2378F

Бренды по названию

Популярные бренды