Renesas Emulation Pod M3062NT3-RPD-E Скачать руководство пользователя страница 26

Страница: 26 / 86

( 24 / 84 )

(2) Inside of the Emulation Pod

Figure 2.2 Internal view of the emulation pod

(1) MCU-dependent board 1

This is a board for port emulation.

(2) MCU-dependent board 2

This is a board with the evaluation MCU.

(3) Common board

This is a board controlling the interface with the PC4701 and evaluation MCU.

(4) Oscillator circuit board

This is a board with an oscillator module. You can change the operating frequency by replacing
it with other oscillator circuit board included with this product package.

(3) Common board

(2) MCU-dependent Board 2

(1) MCU-dependent board

(4) Oscillator circuit board

Содержание Emulation Pod M3062NT3-RPD-E






















































































Результаты поиска

Содержание Emulation Pod M3062NT3-RPD-E

Отзывы:

Похожие инструкции для Emulation Pod M3062NT3-RPD-E

Бренды по названию

Популярные бренды

Renesas Emulation Pod M3062NT3-RPD-E, Руководство пользователя

Результаты поиска

Содержание Emulation Pod M3062NT3-RPD-E

Отзывы:

Похожие инструкции для Emulation Pod M3062NT3-RPD-E

Бренды по названию

Популярные бренды