Renesas Emulation Pod M3062NT3-RPD-E Скачать руководство пользователя страница 56

Страница: 56 / 86

( 54 / 84 )

Chapter 4. Usage

4.1 Turning On the Power

(1) Checking Connections of the Emulator System

Before turning the power ON, check the connections of the PC4701, emulation pod, converter board
and target system.

(2) Turning ON/OFF the Power

• Turn on the power of the emulator and target system as simultaneously as possible.

• Turn off the power of the emulator and target system as simultaneously as possible.

• Do not leave either the emulator or target system powered on, because of leakage current the

internal circuits may be damaged.

• When turning on the power again after shutting off the power, wait about 10 seconds.

CAUTION

Notes on Power Supply:

• Pin Vcc of the emulator is connected to the target system to observe the voltage of

the target system. Therefore design your system so that the target system is powered
by an external power supply.

• The voltage of the target system should be within the MCU's specified range.

• Do not change target system power supply voltage after power has been activated.

Содержание Emulation Pod M3062NT3-RPD-E






















































































Результаты поиска

Содержание Emulation Pod M3062NT3-RPD-E

Отзывы:

Похожие инструкции для Emulation Pod M3062NT3-RPD-E

Бренды по названию

Популярные бренды

Renesas Emulation Pod M3062NT3-RPD-E, Руководство пользователя

Результаты поиска

Содержание Emulation Pod M3062NT3-RPD-E

Отзывы:

Похожие инструкции для Emulation Pod M3062NT3-RPD-E

Бренды по названию

Популярные бренды