Renesas Emulation Pod M3062NT3-RPD-E Скачать руководство пользователя страница 30

Страница: 30 / 86

( 28 / 84 )

Chapter 3. Setting Up

To use this emulation pod with your target system, it is necessary to set as follows. Set the following
after removing the upper cover.

• Input frequency
• Switches
• Pullup resistors
• A-D conversion bypass capacitor

3.1 Removing and Closing the Upper Cover

(1) To open the upper cover, remove the four screws of both sides of this product and lift off the upper

cover (see Figure 3.1).

(2) To close the upper cover, attach the upper cover and secure the four screws of both sides of this

product.

Figure 3.1 Removing the upper cover

CAUTION

When Removing and Closing the Upper Cover:

• Always shut OFF power before opening the upper cover to change the switch

settings.

• Do not touch the connector pins of the PC4701 and the target MCU connector pins.

Static electricity may damage the internal circuits.

Содержание Emulation Pod M3062NT3-RPD-E






















































































Результаты поиска

Содержание Emulation Pod M3062NT3-RPD-E

Отзывы:

Похожие инструкции для Emulation Pod M3062NT3-RPD-E

Бренды по названию

Популярные бренды

Renesas Emulation Pod M3062NT3-RPD-E, Руководство пользователя

Результаты поиска

Содержание Emulation Pod M3062NT3-RPD-E

Отзывы:

Похожие инструкции для Emulation Pod M3062NT3-RPD-E

Бренды по названию

Популярные бренды