background image

10

REMKO PGM (E) series

Setting and controlling 
the heating capacity

 The desired or required heating 
capacity can be steplessly set 
on the “

power regulation

”.

 

The heating capacity can also be 
steplessly changed during unit 
operation.

Safety distances

   For safe operation, a 1 m safety 

distance must be maintained 
around the unit

   A minimum distance of 3 m 

must be maintained from 
the unit outlet

   Flooring and ceilings must be 

fire retardant

Ventilate

In this operating mode, the supply 
air fan runs permanently. 
The units can be used for air 
recirculation or ventilation 
purposes.

1.   Close the shut off valve(s) 

of the gas supply system and 
allow the gas flame to burn out.

2.   Move the operating 

switch to the "II" 
(Ventilate) position.

No heating operation is possible 
in this operating mode.

Heating mode 

1.  Move the operating 

switch to the "I" position. 

The supply air fan starts 
up

.

2.  Push in the pressure 

pin 2 of 
the safety pilot 
and hold down. 

3.  With pressure 

pin 2 depressed, 
after approx. 2 to 3 
sec.actuate 
the piezo igniter 3. 
 
If necessary, actuate 
the piezo igniter multiple times.

4.  After a flame appears, depress 

the pressure pin 2 for a further 
approx. 10-15 sec. until 
the thermal flame monitoring 
is activated.

5.  If the flame goes out when 

the pressure pin 2 is released, 
repeat the ignition process. 

Observe a waiting time of 
approx. 1 minute.

 With a repeat ignition process, 
hold the pressure pin for a little 
longer if necessary.

2

3

Turning to the left:

higher heating capacity

Turning to the right:

lower heating capacity

CAUTION

Before executing the 
ignition process, check to 
ensure the correct function 
of the supply air fan.

CAUTION

The units must not be used 

below ground level

, e.g. 

in basements, without suitable 
gas monitoring equipment.

CAUTION

In case of a gas leak, halt unit 
operation immediately.  
All gas shut-off valves must 
be closed and the units 
disconnected from the power 
supply.

CAUTION

It is essential to observe 
the necessary safe distances 
from flammable and fire 
hazardous materials.

CAUTION

It must be ensured that supply 
air can be freely sucked in and 
that heated air can be blown 
out without obstruction.
The unit intake and outlet 
must not be restricted or fitted 
with hoses or pipes.

NOTE

Overpressure and underpressure 
in the installation area 
should be avoided as this will 
inevitably lead to combustion-
related faults.

Содержание PGM 30

























Отзывы: