REMKO HTL 200-EC Скачать руководство пользователя страница 21

21

Spare parts list

When ordering spare parts, please state the EDP no.

unit number and type

 

(see name plate)!

No.

HTL 200-EC

HTL 250-EC

EDP no.

EDP no.

1

Cover panel, rear

1105335

1105335

2

Collar for exhaust gas nozzle

1103023

1103023

3

Connection profile

1105312

1105312

4

Cover panel, front

1105336

1105336

5

Crane eye

1102554

1102554

6

Insulation, top

1105433

1105433

7

Insulation, left/right

1105413

1105413

8

Casing panel, lateral, rear (left/right)

1105339

1105339

9

Casing panel, lateral, front (left/right)

1105411

1105411

10

Outlet nozzle

1105341

1105341

11

Mounting rail, front/rear

1105414

1105414

12

Mounting panel for oil filter

1105342

1105342

13

Lockable door on burner 

1105382

1105382

14

Oil filter with stopcock

1102526

1102526

15

Oil basin

1105344

1105344

16

Substructure

1105345

1105345

17

Mounting panel, electrical

1105346

1105346

18

Double socket

1105408

1105408

19

Distribution box

1105409

1105409

20

Base plate

1105386

1105386

21

Insulation, bottom

1105347

1105347

22

Partition, front

1105352

1105352

23

Outlet nozzle

1103029

1103029

24

Fan support

1105388

1105388

25

Oil pre-heater

1105301

1105301

26

Fan base

1105297

1105297

27

EC-fan

1105258

1105298

28

Thermostat receptacle bracket

1102048

1102048

29

Suction panel with inlet nozzle

1105279

1105279

30

Casing panel, rear (with protection grid)

1105278

1105278

31

Snap lock with padlock

1105302

1105302

32

Lockable door, electrical

1105398

1105398

33

Switching cabinet, compl.

1105259

1105259

34

Sealing panel

1105448

1105448

35

Insulation, top, rear

1105449

1105449

36

Complete unit frame

1105463

1105463

37

Mounting panel for switch box 

1105403

1105403

38

Sealing cap

1103032

1103032

39

Complete forced-air oil burner 

948510

948510

40

Burner flange

1108539

1108539

41

Flange seal

1108538

1108538

42

Complete combustion chamber with heat exchanger 

1103055

1105381

43

Exhaust gas suppressor, set 

1105299

1105299

44

Seal for inspection cover

1105406

1105406

45

Inspection cover

1105407

1105407

46

Exhaust pipe nozzle

1105360

1105360

47

Seal for exhaust pipe nozzle 

1103020

1103020

xx

Triple-function combination controller

1102562

1102562

xx

Mains cable with plug

1105362

1105362

xx

Thermostat plug (accessory) 

1101020

1101020

xx

Strapping plug

1101019

1101019

xx

Seal for cover panel, rear

1105452

1105452

xx = not illustrated

Содержание HTL 200-EC





























Отзывы: