Remington 100582-01, 100582-02 страница 13 Скачать руководство пользователя

Страница: 13 / 36

101241

CLEANING AND MAINTENANCE

Continued

Sharpening Cutters

Use file guide for 30° filing.
1. Adjust chain for proper tension (see Saw Chain Tension

Adjustment, page 7).

2. Clamp guide bar in vise to hold saw steady.

Note:

Do not

clamp chain.

3. Press four millimeter (5/32") round file (attached to file

guide) into groove between top plate and depth gauge on
chain. File guide should rest on both top plate and depth
gauge (see Figures 20 and 21).

Note:

File at midpoint of

guide bar.

4. Hold file guide level. Make sure 30° mark on file guide is

parallel to center of guide bar (see Figure 20). This will
insure that you file cutters at 30° angle.

5. File from inside towards outside of cutter until sharp.

Only file in this one direction (see Figure 20).

Note:

Two

or three strokes with file should sharpen cutter.

6. After each cutter if sharpened, move chain forward to

sharpen next cutter. File all cutters on one side of chain.

7. Move to other side of chain and repeat process.

Top Plate
(left side
of chain)

Groove

Depth Gauge
(left side
of chain)

Groove

Depth Gauge
(right side of chain)

Top Plate
(right side of chain)

Left Side
of Chain

Right Side
of Chain

Figure 21 - Chain Part Locations

Flat File

Depth
Gauge
Tool

Depth Gauge

Depth
Gauge
Slot

Figure 22 - Depth Gauge Tool On Chain

Continued

ECSp005

Figure 23 - Round Off Front Corner Of Depth Gauge

Front Corner

After several hand filings, have authorized service center or
sharpening service machine sharpen chain. This will insure
even filing.

Filing Cutter Depth Gauges

The cutter depth gauge clearance is reduced as cutters are
sharpened. After every second or third sharpening, reset cutter
depth gauges.
1. Place depth gauge tool firmly across top of two cutters.

Make sure depth gauge enters slot in depth gauge tool (see
Figure 22).

2. Use medium flat file. File depth gauge level with depth

gauge tool.

3. Remove depth gauge tool. With flat file, round off front

corner of cutter depth gauge (see Figure 23).

30° Guide
Mark

File Guide

4 mm (5/32")
Round File

Note: This
illustration
shows file
guide place-
ment and filing
direction for
sharpening
cutters on left
side of chain.

Filing
Direction

Figure 20 - File and File Guide Placement On Chain

Содержание 100582-01, 100582-02





































Результаты поиска

Содержание 100582-01, 100582-02

Отзывы:

Похожие инструкции для 100582-01, 100582-02

Бренды по названию

Популярные бренды

Remington 100582-01, 100582-02, Руководство пользователя

Результаты поиска

Содержание 100582-01, 100582-02

Отзывы:

Похожие инструкции для 100582-01, 100582-02

Бренды по названию

Популярные бренды