REMEHA Gas 120 ACE - 115 Скачать руководство пользователя страница 65

Страница: 65 / 96

Code

Display text

Description

Range

Submenu

Zone SysTReturn

Current system return

temperature from power

manager of the zone

-327.68 °C - 327.67 °C

Zone manager

Request P to PM

Request from the producer to

the producer manager to take

action

Producer Generic

Producer<>Consumer

Prod. manager bridge

Actual power PM

Actual power sent from the

producer manager

0 % - 100 %

Producer Generic

Producer<>Consumer

Prod. manager bridge

Time update stat

Time update status for devices

communicating via the RUbus

Time R to L/S-bus

AM024

Actual rel. Power

Actual relative power of the

appliance

0 % - 100 %

Gas fired appliance

AM036

Flue gas

temperature

Temperature of the exhaust gas

leaving the appliance

0 °C - 250 °C

Gas fired appliance

AM043

Pwr dwn reset

needed

A power down reset is needed

0 = No

1 = Yes

Gas fired appliance

AM101

Internal setpoint

Internal system flow

temperature setpoint

0 °C - 250 °C

Gas fired appliance

DM001

DHW tank temp

bottom

Domestic Hot Water tank

temperature (bottom sensor)

-25 °C - 150 °C

Tank DHW

DM005

DhwSolarTankTe

Domestic Hot Water solar tank

temperature

-25 °C - 150 °C

Internal DHW

Tank DHW

DM008

DHW out temp

Temperature sensor for the tap

temperature leaving the

appliance

-25 °C - 150 °C

Internal DHW

GM025

STB status

High limit status (0 = open, 1 =

closed)

0 = Open

1 = Closed

2 = Off

Gas fired appliance

GM027

Flame Test Active Flame test 1=active, 0=inactive 0 = Inactive

1 = Active

Gas fired appliance

GM044

ControlledStopRe

ason

Possible reason for Controlled

Stop

0 = None

1 = CH Blocking

2 = DHW Blocking

3 = Wait for burner

4 = TFlow > absolute max

5 = TFlow > start temp.

6 = Theat exch. > Tstart

7 = Avg Tflow > Tstart

8 = TFlow > max setpoint

9 = T difference too big

10 = TFlow > stop temp.

11 = Anti cycle on off HD

Gas fired appliance

PM002

CH Setpoint

External winning Central

Heating setpoint

0 °C - 250 °C

Gas fired appliance

PM003

ChTflowAverage

Actual average flow

temperature

-25 °C - 150 °C

Gas fired appliance

Tab.52 Navigation for advanced installer level

Level

Menu path

Advanced installer

> Installation Setup > CU-GH08 > Submenu

(1)

> Parameters, counters, signals > Signals > Adv.

Signals

(1) See the column "Submenu" in the following table for the correct navigation. The signals are grouped in specific functionalities.

9 Settings

7717201 - v03 - 25062019

MID _HMI T-control - Gas 120 ACE

Содержание Gas 120 ACE - 115

































































































Результаты поиска

Содержание Gas 120 ACE - 115

Отзывы:

REMEHA Gas 120 ACE - 115, Руководство пользователя, Страница: 65 / 96

Результаты поиска

Содержание Gas 120 ACE - 115

Отзывы: