Reloop CONTOUR, Инструкция по эксплуатации

Страница: 19 / 52

ENGLI
sh
19
tion to this device any warrantyclaims are excluded.
- The inside of the device does not contain any parts which require maintenance, with the excep-
tion of wear parts that can be exchanged from the outside. Only qualified staff must carry out
maintenance, otherwise warranty does not apply!
- The Fuse must exclusively be exchanged against fuses of the same class, with the same trigger
features and nominal current rating.
- Make sure that the power will only be supplied after the device has been fully set up. Always plug
in the mains plug last. Ensure that the mains switch is in the “OFF” position when connecting the
device to power.
- Only use cables that comply with regulations. Observe that all jacks and bushes are tightened
and correctly hooked up. Refer to your dealer if you have any questions.
- Ensure that when setting up the product the mains cable is not squashed or damaged by sharp
edges.
- Prevent the mains cable from coming into contact with other cables! Exercise great care when
handling mains cables and connections. Never touch these parts with wet hands!
- Connect the power cable exclusively to appropriate shock-proof outlets. The only supply point to
be used is a supply outlet in accordance with specifications of the public supply network.
- Disconnect the device from the supply outlet when not in use and before cleaning! Be sure to
hold the mains plug by the body. Never pull the mains cord!
- Position the device on a horizontal and stable low-flame base.
- Avoid any concussions or violent impact when installing or operating the device.
- When selecting the location of installation make sure that the device is not exposed to excessive
heat, humidity, and dust. Be sure that no cables lie around openly. You will endanger your own
safety and that of others!
- Do not rest any containers filled with liquid that could easily spill onto the device or in its imme-
diate vicinity. If, however, fluids should access the inside of the device, immediately disconnect
the mains plug. Have the device checked by a qualified service technician before re-use. Damage
caused by fluids inside the device is excluded from the warranty.
- Do not operate the device under extremely hot (in excess of 35° C) or extremely cold (below 5°
C) conditions. Keep the device away from direct exposure to the sun and heat sources such as
radiators, ovens, etc. (even during transport in a closed vehicle). Never cover the cooling fan or
vents. Always ensure sufficient ventilation.
- The device must not be operated after being taken from a cold environment into a warm environ-
ment. The condensation caused hereby may destroy your device. Do not switch on or operate the
device until it has reached ambient temperature!
- Controls and switches should never be treated with spray-on cleaning agents and lubricants. This
device should only be cleaned with a damp cloth. Never use solvents or cleaning fluids with a
petroleum base for cleaning.
- When relocating, the device should be transported in its original packaging.
- When starting operation, the faders and volume controls of your amplifier must be set to mini-
mum level. Bring the loudspeaker switches into the “OFF” position. Wait between 8 to 10 seconds
before increasing the volume to avoid shot noise created by transient effect, which could cause
damage to loudspeakers and the diplexer.
- Devices supplied by voltage should not be left in the hands of children. Please exercise particular
care when in the presence of children.
- At commercial facilities the regulations for the prevention of accidents as stipulated by the orga-
nization of professional associations must be observed.
- At schools, training facilities, hobby and self-help workshops the operation of the device must be
monitored with responsibility by trained staff.
- Keep this operation manual in a safe place for later reference in the event of questions or prob-
lems.
APPLICATION IN ACCORDANCE WITh REGULATIONs
- This device is a professional DJ MIDI controller with integrated 8 channel soundcard that can
control software. The device should be connected via USB cable to a computer.
- This product is authorised for connection to switching power AC 100-240V, 50/60Hz via an optio-
nally available mains adapter and is designed exclusively for indoor application.
- If the device is used for any other purposes than those described in the operation manual, da-
mage can be caused to the product, leading to exclusion of warranty rights. Moreover, any other